- 您現在的位置：買賣IC網 > PDF目錄383108 > ILX554B (Sony Corporation) 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader PDF資料下載
參數資料
| 型號： | ILX554B |
| 廠商： | Sony Corporation |
| 英文描述： | 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader |
| 中文描述： | 2048像素CCD線性傳感器（黑/白）為單5V電源條碼閱讀器 |
| 文件頁數： | 11/13頁 |
| 文件大小： | 106K |
| 代理商： | ILX554B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁
–
11
–
ILX554B
Upper ceramic layer
39N
Lower ceramic layer
Low-melting glass
(1)
29N
(3)
0.9Nm
(4)
29N
(2)
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling, be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive
shoes.
b) When handling directly use an eath band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) lonized air is recommended for discharge when handling CCD image sensors.
e) For the shipment of mounted substrates use cartons treated for the prevention of static charges.
2) Notes on handling CCD Cer-DIP package
The following points should be observed when handling and installing this package.
a) (1) Compressive strength: 39N/surface
(Do not apply any load more than 0.7mm inside the outer perimeter of the glass portion.)
(2) Shearing strength:
29N/surface
(3) Tensile strength:
29N/surface
(4) Torsional strength:
0.9Nm
b) In addition, if a load is applied to the entire surface by a hard component, bending stress may be
generated and the package may fracture, etc., depending on the flatness of the ceramic portion.
Therefore, for installation, either use an elastic load, such as a spring plate, or an adhesive.
c) Be aware that any of the following can cause the glass to crack because the upper and lower ceramic
layers are shielded by low-melting glass.
(1) Applying repetitive bending stress to the external leads.
(2) Applying heat to the external leads for an extended period of time with a soldering iron.
(3) Rapid cooling or heating.
(4) Applying a load or impact to a limited portion of the low-melting glass with a small-tipped tool such
as tweezers.
(5) Prying the upper or lower ceramic layers away at a support point of the low-melting glass.
Note that the preceding notes should also be observed when removing a component from a board after
it has already been soldered.
3) Soldering
a) Make sure the package temperature does not exceed 80
°
C.
b) Solder dipping in a mounting furnace causes demage to the glass abd other defects. Use a grounded
30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool
sufficiently.
c) To dismount image sensors, do not use a solder suction equipment. When using an electric desoldering
tool, ground the controller. For the control system, use a zero cross type.
相關PDF資料 |
PDF描述 |
|---|---|
| ILX554 | 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader |
| ILX554A | 2048-pixel CCD Linear Sensor (B/W) for Single 5V Power Supply Bar-code Reader |
| ILX555K | 10680 pixel 】 3 line CCD Linear Sensor (Color) |
| ILX558K | 5340-pixel 】 3-line CCD Linear Sensor (Color) |
| ILX569K | 5340-pixel x 6 line CCD Linear Sensor (Color) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ILX555K | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:10680 pixel 】 3 line CCD Linear Sensor (Color) |
| ILX558K | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:5340-pixel 】 3-line CCD Linear Sensor (Color) |
| ILX569K | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:5340-pixel x 6 line CCD Linear Sensor (Color) |
| ILX585K | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:pixel 】 6line CCD Linear Sensor (Color) |
| ILX703A | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:2048-pixel CCD Linear Image Sensor (B/W) with Shutter Function |
發布緊急采購，3分鐘左右您將得到回復。