- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82P2816BBG (IDT, Integrated Device Technology Inc)IC LINE INTERFACE UNIT 416-PBGA PDF資料下載
參數資料
| 型號： | IDT82P2816BBG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 46/146頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE INTERFACE UNIT 416-PBGA |
| 標準包裝： | 5 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 1 |
| 電源電壓： | 1.8V, 3.3V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 416-BGA |
| 供應商設備封裝： | 416-PBGA（27x27） |
| 包裝： | 托盤 |
| 包括： | 缺陷和警報檢測，驅動器過流檢測和保護，LLOS 檢測，PRBSARB / IB 檢測和生成 |
| 產品目錄頁面： | 1259 (CN2011-ZH PDF) |
| 其它名稱： | 800-1702 82P2816BBG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁
IDT82P2816
16(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Pin Description
14
February 6, 2009
2
PIN DESCRIPTION
Name
I / O
Pin No. 1
Description
Line Interface
RTIPn
RRINGn
(n=0~16)
Input
K4, M3, P4, T3, V4, V24, T23, P24,
M23, K24, H23, F24, C24, D5, C3,
F4, H3
J4, L3, N4, R3, U4, U24, R23, N24,
L23, J24, G23, E24, C23, D6, C4,
E4, G3
RTIPn / RRINGn: Receive Bipolar Tip/Ring for Channel 0 ~ 16
The receive line interface supports both Receive Differential mode and Receive Single Ended
mode.
In Receive Differential mode, the received signal is coupled into RTIPn and RRINGn via a 1:1
transformer or without a transformer (transformer-less).
In Receive Single Ended mode, RRINGn should be left open. The received signal is input on
RTIPn via a 2:1 (step down) transformer or without a transformer (transformer-less).
These pins will become High-Z globally or channel specific in the following conditions:
Global High-Z:
- Connecting the RIM pin to low;
- Loss of MCLK
- During and after power-on reset, hardware reset or global software reset;
Per-channel High-Z
- Receiver power down by writing ‘1’ to the R_OFF bit (b5, RCF0,...)
TTIPn
TRINGn
(n=0~16)
Output
K1, M1, P1, T1, V1, V26, T26, P26,
M26, K26, H26, F26, A24, A5, A3,
F1, H1
J1, L1, N1, R1, U1, U26, R26, N26,
L26, J26, G26, E26, A23, A6, A4,
E1, G1
TTIPn / TRINGn: Transmit Bipolar Tip /Ring for Channel 0 ~ 16
The transmit line interface supports both Transmit Differential mode and Transmit Single
Ended mode.
In Transmit Differential mode, TTIPn outputs a positive differential pulse while TRINGn out-
puts a negative differential pulse. The pulses are coupled to the line side via a 1:2 (step up)
transformer or without a transformer (transformer-less).
In Transmit Single Ended mode, TRINGn should be left open (it is shorted to ground inter-
nally). The signal presented at TTIPn is output to the line side via a 1:2 (step up) transformer.
These pins will become High-Z globally or channel specific in the following conditions:
Global High-Z:
- Connecting the OE pin to low;
- Loss of MCLK;
- During and after power-on reset, hardware reset or global software reset;
Per-channel High-Z
- Loss of TCLKn in Transmit Single Rail NRZ Format mode or Transmit Dual Rail NRZ
Format mode, except that the channel is in Remote Loopback or transmit internal pat-
tern with XCLK 3;
- Transmitter power down by writing ‘1’ to the
T_OFF bit (b5, TCF0,...);
- Per-channel software reset;
- The THZ_OC bit (b4, TCF0,...) is set to ‘1’ and the transmit driver over-current is
detected.
Refer to Section 3.3.8 Output High-Z on TTIP and TRING for details.
Note:
1. The pin number of the pins with the footnote ‘n’ is listed in order of channel (CH0 ~ CH16).
2. The content in the brackets indicates the position and the register name of the preceding bit. After the register name, if the punctuation ‘,...’ is followed, this bit is in a per-channel register.
If there is no punctuation following the address, this bit is in a global register or in a channel 0 only register. The addresses and details are included in Chapter 5 Programming Information.
3. XCLK is derived from MCLK. It is 1.544 MHz in T1/J1 mode or 2.048 MHz in E1 mode.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82P2821BH | IC LIU T1/J1/E1 21+1CH 640-PBGA |
| IDT82P2828BHG | IC LIU T1/J1/E1 28+1CH 640-PBGA |
| IDT82P2916BFG | IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P5088BBG | IC LIU T1/E1/J1 OCTAL 256PBGA |
| IDT82V2041EPPG | IC LIU T1/J1/E1 1CH 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P2821 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:21(+1) Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2821BH | 功能描述:IC LIU T1/J1/E1 21+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| IDT82P2821BHG | 功能描述:IC LINE INTERFACE UNIT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| IDT82P2828 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:28(+1) Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2828BH | 功能描述:IC LIU T1/J1/E1 28+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。