IDT72V263/273/283/293/103/113 3.3V HIGH DENSITY SUPERSYNC IITM NARROW BUS FIFO" />
參數資料
型號： IDT72V273L10PFG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 41/45頁
文件大?。?/td> 0K
描述： IC FIFO SYNC II 3.3V 80-TQFP
標準包裝： 45
系列： 72V
功能： 同步
存儲容量： 288K（16K x 18）
數據速率： 166MHz
訪問時間： 10ns
電源電壓： 3.15 V ~ 3.45 V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 80-LQFP
供應商設備封裝： 80-TQFP（14x14）
包裝： 托盤
產品目錄頁面： 1255 (CN2011-ZH PDF)
其它名稱： 72V273L10PFG
800-1524
5
IDT72V263/273/283/293/103/113 3.3V HIGH DENSITY SUPERSYNC IITM NARROW BUS FIFO
8K x 18, 16K x 9/18, 32K x 9/18, 64K x 9/18, 128K x 9/18, 256K x 9/18, 512K x9
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT72V223/233/243/253/263/273/283/293 3.3V HIGH DENSITY SUPERSYNC IITM NARROW BUS FIFO
512 x 18, 1K x 9/18, 2K x 9/18, 4K x 9/18, 8K x 9/18, 16K x 9/18, 32K x 9/18, 64K x 9/18, 128K x 9
FEBRUARY 11, 2009
to-HIGH transition of WCLK. Similarly, the
PAFisassertedLOWontheLOW-
to-HIGH transition of WCLK and
PAF is reset to HIGH on the LOW-to-HIGH
transition of RCLK.
If synchronous
PAE/PAF configuration is selected , the PAE is asserted
and updated on the rising edge of RCLK only and not WCLK. Similarly,
PAF
is asserted and updated on the rising edge of WCLK only and not RCLK. The
modedesiredisconfiguredduringmasterresetbythestateoftheProgrammable
Flag Mode (PFM) pin.
The Retransmit function allows data to be reread from the FIFO more
than once. A LOW on the
RT input during a rising RCLK edge initiates a
retransmitoperationbysettingthereadpointertothefirstlocationofthememory
array. A zero-latency retransmit timing mode can be selected using the
RetransmittimingModepin(RM).DuringMasterReset,aLOWonRMwillselect
zero-latency retransmit. A HIGH on RM during Master Reset will select normal
latency.
If zero-latency retransmit operation is selected the first data word to be
retransmitted will be placed on the output register with respect to the same
RCLK edge that initiated the retransmit based on RT being LOW.
Refer to Figure 11 and 12 for Retransmit Timing with normal latency. Refer
to Figure 13 and 14 for Retransmit Timing with zero-latency.
A Big-Endian/Little-Endian data word format is provided. This function is
useful when data is written into the FIFO in long word format (x18) and read
out of the FIFO in small word (x9) format. If Big-Endian mode is selected, then
themostsignificantbyte(word)ofthelongwordwrittenintotheFIFOwillberead
IW
OW
Write Port Width
Read Port Width
L
x18
L
H
x18
x9
H
L
x9
x18
H
x9
TABLE 1 — BUS-MATCHING CONFIGURATION MODES
outoftheFIFOfirst,followedbytheleastsignificantbyte.IfLittle-Endianformat
is selected, then the least significant byte of the long word written into the FIFO
will be read out first, followed by the most significant byte. The mode desired is
configured during master reset by the state of the Big-Endian (
BE) pin.
The Interspersed/Non-Interspersed Parity (IP) bit function allows the user
to select the parity bit in the word loaded into the parallel port (D0-Dn) when
programming the flag offsets. If Interspersed Parity mode is selected, then the
FIFOwillassumethattheparitybitislocatedinbitpositionD8 duringtheparallel
programmingoftheflagoffsets.IfNon-InterspersedParitymodeisselected,then
D8isassumedtobeavalidbitandD16 andD17 areignored.IPmodeisselected
during Master Reset by the state of the IP input pin. This mode is relevant only
when the input width is set to x18 mode. Interspersed Parity control only has
aneffectduringparallelprogrammingoftheoffsetregisters.Itdoesnoteffectthe
data written to and read from the FIFO.
A JTAG test port is provided, here the FIFO has fully functional Boundary
Scan feature, compliant with IEEE 1149.1 Standard Test Access Port and
Boundary Scan Architecture.
If, at any time, the FIFO is not actively performing an operation, the chip will
automatically power down. Once in the power down state, the standby supply
currentconsumptionisminimized.Initiatinganyoperation(byactivatingcontrol
inputs) will immediately take the device out of the power down state.
The IDT72V223/72V233/72V243/72V253/72V263/72V273/72V283/
72V293 are fabricated using IDT’s high speed submicron CMOS technology.
相關PDF資料
PDF描述
VE-J72-MX-S CONVERTER MOD DC/DC 15V 75W
VE-26M-CU-F3 CONVERTER MOD DC/DC 10V 200W
IDT72V3640L7-5PFGI IC FIFO SYNC II 36BIT 128-TQFP
MS27468T17B26PB CONN RCPT 26POS JAM NUT W/PINS
SF7282-3SG-3ES CONN RCPT 3POS PNL MNT SKT
相關代理商/技術參數
參數描述
IDT72V273L10PFG8 制造商:Integrated Device Technology Inc 功能描述:IC FIFO 16384X18 10NS 80QFP
IDT72V273L10PFI 功能描述:IC FIFO 16384X18 10NS 80QFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433
IDT72V273L10PFI8 功能描述:IC FIFO 16384X18 10NS 80QFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF
IDT72V273L15PF 功能描述:IC FIFO 16384X18 15NS 80QFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF
IDT72V273L15PF8 功能描述:IC FIFO 16384X18 15NS 80QFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:72V 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*