參數資料
型號： ID80C86
廠商： INTERSIL CORP
元件分類： 微控制器/微處理器
英文描述： CMOS 16-Bit Microprocessor
中文描述： 16-BIT, 5 MHz, MICROPROCESSOR, CDIP40
封裝： CERDIP-40
文件頁數： 5/35頁
文件大?。?/td> 339K
代理商： ID80C86
3-145
INTR
18
I
INTERRUPT REQUEST: is a level triggered input which is sampled during the last clock cycle
of each instruction to determine if the processor should enter into an interrupt acknowledge op-
eration. A subroutine is vectored to via an interrupt vector lookup table located in system mem-
ory. It can be internally masked by software resetting the interrupt enable bit.
lNTR is internally synchronized. This signal is active HIGH.
TEST
23
I
TEST: input is examined by the “Wait” instruction. If the TEST input is LOW execution continues,
otherwise the processor waits in an “Idle” state. This input is synchronized internally during each
clock cycle on the leading edge of CLK.
NMI
17
I
NON-MASKABLE INTERRUPT: is an edge triggered input which causes a type 2 interrupt. A
subroutine is vectored to via an interrupt vector lookup table located in system memory. NMI is
not maskable internally by software. A transition from LOW to HIGH initiates the interrupt at the
end of the current instruction. This input is internally synchronized.
RESET
21
I
RESET: causes the processor to immediately terminate its present activity. The signal must tran-
sition LOW to HIGH and remain active HIGH for at least four clock cycles. It restarts execution,
as described in the Instruction Set description, when RESET returns LOW. RESET is internally
synchronized.
CLK
19
I
CLOCK: provides the basic timing for the processor and bus controller. It is asymmetric with a
33% duty cycle to provide optimized internal timing.
VCC
40
VCC: +5V power supply pin. A 0.1
μ
F capacitor between pins 20 and 40 is recommended for de-
coupling.
GND
1, 20
GND: Ground. Note: both must be connected. A 0.1
μ
F capacitor between pins 1 and 20 is rec-
ommended for decoupling.
MN/MX
33
I
MINIMUM/MAXIMUM: Indicates what mode the processor is to operate in. The two modes are
discussed in the following sections.
Minimum Mode System
The following pin function descriptions are for the 80C86 in minimum mode (i.e., MN/MX = V
CC
). Only the pin functions which are unique to
minimum mode are described; all other pin functions are as described below.
SYMBOL
PIN
NUMBER
TYPE
DESCRIPTION
M/IO
28
O
STATUS LINE: logically equivalent to S2 in the maximum mode. It is used to distinguish a mem-
ory access from an I/O access. M/lO becomes valid in the T4 preceding a bus cycle and remains
valid until the final T4 of the cycle (M = HIGH, I/O = LOW). M/lO is held to a high impedance logic
one during local bus “hold acknowledge”.
WR
29
O
WRITE: indicates that the processor is performing a write memory or write I/O cycle, depending
on the state of the M/IO signal. WR is active for T2, T3 and TW of any write cycle. It is active
LOW, and is held to high impedance logic one during local bus “hold acknowledge”.
INTA
24
O
INTERRUPT ACKNOWLEDGE: is used as a read strobe for interrupt acknowledge cycles. It is
active LOW during T2, T3 and TW of each interrupt acknowledge cycle. Note that INTA is never
floated.
ALE
25
O
ADDRESS LATCH ENABLE: is provided by the processor to latch the address into the
82C82/82C83 address latch. It is a HIGH pulse active during clock LOW of T1 of any bus cycle.
Note that ALE is never floated.
Pin Description
(Continued)
The following pin function descriptions are for 80C86 systems in either minimum or maximum mode. The “Local Bus” in these description is
the direct multiplexed bus interface connection to the 80C86 (without regard to additional bus buffers).
SYMBOL
PIN
NUMBER
TYPE
DESCRIPTION
80C86
相關PDF資料
PDF描述
ID80C86-2 CMOS 16-Bit Microprocessor
ID80C88 CMOS 8/16-Bit Microprocessor
ID80C88-2 CMOS 8/16-Bit Microprocessor
ID82C284-10 Clock Generator and Ready Interface for 80C286 Processors
ID82C284-12 Clock Generator and Ready Interface for 80C286 Processors
相關代理商/技術參數
參數描述
ID80C86-2 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 16-Bit Microprocessor
ID80C88 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 8/16-Bit Microprocessor
ID80C88-2 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:CMOS 8/16-Bit Microprocessor
ID810 制造商:IBase Technology (USA) Inc. 功能描述:FC, ID810 XGI Z11 VGA/LVDS, FOR ECX810, (ROHS) - Bulk
ID-8-100 功能描述:WRAP ID SOCKET .3" SPACE 8PIN RoHS:否 類別:連接器，互連式 >> 用于 IC 的插座，晶體管 - 配件 系列:- 標準包裝:1 系列:- 附件類型:安裝套件 適用于相關產品:12-SIP 其它名稱:598-1366
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*