- 您現在的位置：買賣IC網 > PDF目錄383088 > ICL7663S (Intersil Corporation) High-Performance Impact<TM> PAL<R> Circuits 24-CDIP -55 to 125 PDF資料下載
參數資料
| 型號： | ICL7663S |
| 廠商： | Intersil Corporation |
| 英文描述： | High-Performance Impact<TM> PAL<R> Circuits 24-CDIP -55 to 125 |
| 中文描述： | CMOS可編程微正電壓穩壓器 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 158K |
| 代理商： | ICL7663S |
59
Detailed Description
The ICL7663S is a CMOS integrated circuit incorporating all
the functions of a voltage regulator plus protection circuitry
on a single monolithic chip. Referring to the Functional
Diagram, the main blocks are a bandgap-type voltage
reference, an error amplifier, and an output driver with both
PMOS and NPN pass transistors.
The bandgap output voltage, trimmed to 1.29V
±
15mV for
the ICL7663SA, and the input voltage at the V
SET
terminal
are compared in amplifier A. Error amplifier A drives a
P-channel pass transistor which is sufficient for low (under
about 5mA) currents. The high current output is passed by
an NPN bipolar transistor connected as a follower. This
configuration gives more gain and lower output impedance.
Logic-controlled shutdown is implemented via a N-Channel
MOS transistor. Current-sensing is achieved with
comparator C, which functions with the V
OUT2
terminal. The
ICL7663S has an output (V
TC
) from a buffer amplifier (B),
which can be used in combination with amplifier A to
generate programmable-temperature-coefficient output
voltages.
The amplifier, reference and comparator circuitry all operate
at bias levels well below 1
μ
A to achieve extremely low
quiescent current. This does limit the dynamic response of
the circuits, however, and transients are best dealt with
outside the regulator loop.
Basic Operation
The ICL7663S is designed to regulate battery voltages in the
5V to 15V region at maximum load currents of about 5mA to
30mA. Although intended as low power devices, power
dissipation limits must be observed. For example, the power
dissipation in the case of a 10V supply regulated down to 2V
with a load current of 30mA clearly exceeds the power
dissipation rating of the Mini-DIP:
(10 - 2) (30) (10
-3
) = 240mW
The circuit of Figure 8 illustrates proper use of the device.
CMOS devices generally require two precautions: every
input pin must go somewhere, and maximum values of
applied voltages and current limits must be rigorously
observed. Neglecting these precautions may lead to, at the
least, incorrect or nonoperation, and at worst, destructive
device failure. To avoid the problem of latchup, do not apply
inputs to any pins before supply voltage is applied.
Input Voltages -
The ICL7663S accepts working inputs of
1.5V to 16V. When power is applied, the rate-of-rise of the
input may be hundreds of volts per microsecond. This is
potentially harmful to the regulators, where internal
operating currents are in the nanoampere range. The
0.047
μ
F capacitor on the device side of the switch will limit
inputs to a safe level around 2V/
μ
s. Use of this capacitor is
suggested in all applications. In severe rate-of-rise cases, it
may be advisable to use an RC network on the SHutDowN
pin to delay output turn-on. Battery charging surges,
transients, and assorted noise signals should be kept from
the regulators by RC filtering, zener protection, or even
fusing.
Output Voltages -
The resistor divider R
2
/R
1
is used to
scale the reference voltage, V
SET
, to the desired output
using the formula V
OUT
= (1 + R
2
/R
1
) V
SET
. Suitable
arrangements of these resistors, using a potentiometer,
enables exact values for V
OUT
to be obtained. In most
applications the potentiometer may be eliminated by using
the ICL7663SA. The ICL7663SA has V
SET
voltage
guaranteed to be 1.29V
±
15mV and when used with
±
1%
tolerance resistors for R
1
and R
2
the initial output voltage
will be within
±
2.7% of ideal.
The low leakage current of the V
SET
terminal allows R
1
and
R
2
to be tens of megohms for minimum additional quiescent
drain current. However, some load current is required for
proper operation, so for extremely low-drain applications it is
necessary to draw at least 1
μ
A. This can include the current
for R
2
and R
1
.
Output voltages up to nearly the V
IN
supply may be obtained
at low load currents, while the low limit is the reference
voltage. The minimum input-output differential in each
regulator is obtained using the V
OUT1
, terminal. The input-
output differential increases to 1.5V when using V
OUT2
.
Output Currents
- Low output currents of less than 5mA are
obtained with the least input-output differential from the
V
OUT1
terminal (connect V
OUT2
to V
OUT1
). Where higher
currents are needed, use V
OUT2
(V
OUT1
, should be left
open in this case).
SHDN
V
OUT2
V
OUT1
V
TC
V
SET
SENSE
GND
1
μ
A MIN
+
-
I
Q
S
2
S
1
R
CL
R
2
R
L
C
L
R
1
(7663 ONLY)
V
OUT
ON
OFF
S
3
1M
1.4V < V
SHDN
< V+
IN
0.047
μ
F
+
-
M
NOTES:
7. S
1
when closed disables output current limiting.
8. Close S
2
for V
OUT1
, open S
2
for V
OUT2
.
9. IQ quiescent currents measured at GND pin by meter M.
10. S
3
when ON, permits normal operation, when OFF, shuts down
both V
OUT1
and V
OUT2
.
FIGURE 7. ICL7663S TEST CIRCUIT
ICL7663S
相關PDF資料 |
PDF描述 |
|---|---|
| ICL7663SACBA | High-Performance Impact<TM> PAL<R> Circuits 24-CFP -55 to 125 |
| ICL7663SACPA | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| ICL7663SCPA | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| ICL7663SIPA | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| ICL7663SCBA | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7663SACBA | 功能描述:線性穩壓器 - 標準 CMOS POS LWPWRG COM RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| ICL7663SACBA-T | 功能描述:線性穩壓器 - 標準 CMOS POS LWPWRG COM TAPE RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| ICL7663SACBAZA | 功能描述:線性穩壓器 - 標準 W/ANNEAL CMOS POS LWPWRG COM RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| ICL7663SACBAZA-T | 功能描述:線性穩壓器 - 標準 W/ANNEAL CMOS POS LWPWRG COM RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| ICL7663SACPA | 功能描述:線性穩壓器 - 標準 CMOS POS LWPWRG COM RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。