- 您現在的位置：買賣IC網 > PDF目錄383079 > ICL3244EIB (INTERSIL CORP) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | ICL3244EIB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | TRIPLE LINE TRANSCEIVER, PDSO28 |
| 封裝： | PLASTIC, MS-013AE, SOIC-28 |
| 文件頁數： | 13/19頁 |
| 文件大小： | 458K |
| 代理商： | ICL3244EIB |
13
Interconnection with 3V and 5V Logic
The ICL32XXE directly interfaces with 5V CMOS and TTL
logic families. Nevertheless, with the ICL32XX at 3.3V, and
the logic supply at 5V, AC, HC, and CD4000 outputs can
drive ICL32XX inputs, but ICL32XX outputs do not reach the
minimum V
IH
for these logic families. See Table 4 for more
information.
±
15kV ESD Protection
All pins on ICL32XX devices include ESD protection
structures, but the ICL32XX
E
family incorporates advanced
structures which allow the RS-232 pins (transmitter outputs
and receiver inputs) to survive ESD events up to
±
15kV. The
RS-232 pins are particularly vulnerable to ESD damage
because they typically connect to an exposed port on the
exterior of the finished product. Simply touching the port
pins, or connecting a cable, can cause an ESD event that
might destroy unprotected ICs. These new ESD structures
protect the device whether or not it is powered up, protect
without allowing any latchup mechanism to activate, and
don’t interfere with RS-232 signals as large as
±
25V.
Human Body Model (HBM) Testing
As the name implies, this test method emulates the ESD
event delivered to an IC during human handling. The tester
delivers the charge through a 1.5k
current limiting resistor,
making the test less severe than the IEC61000 test which
utilizes a 330
limiting resistor. The HBM method
determines an ICs ability to withstand the ESD transients
typically present during handling and manufacturing. Due to
the random nature of these events, each pin is tested with
respect to all other pins. The RS-232 pins on “E” family
devices can withstand HBM ESD events to
±
15kV.
IEC61000-4-2 Testing
The IEC 61000 test method applies to finished equipment,
rather than to an individual IC. Therefore, the pins most likely to
suffer an ESD event are those that are exposed to the outside
world (the RS-232 pins in this case), and the IC is tested in its
typical application configuration (power applied) rather than
testing each pin-to-pin combination. The lower current limiting
resistor coupled with the larger charge storage capacitor yields
a test that is much more severe than the HBM test. The extra
ESD protection built into this device’s RS-232 pins allows the
design of equipment meeting level 4 criteria without the need
for additional board level protection on the RS-232 port.
AIR-GAP DISCHARGE TEST METHOD
For this test method, a charged probe tip moves toward the IC
pin until the voltage arcs to it. The current waveform delivered
to the IC pin depends on approach speed, humidity,
temperature, etc., so it is difficult to obtain repeatable results.
The “E” device RS-232 pins withstand
±
15kV air-gap
discharges.
CONTACT DISCHARGE TEST METHOD
During the contact discharge test, the probe contacts the
tested pin before the probe tip is energized, thereby
eliminating the variables associated with the air-gap
discharge. The result is a more repeatable and predictable
test, but equipment limits prevent testing devices at voltages
higher than
±
8kV. All “E” family devices survive
±
8kV contact
discharges on the RS-232 pins.
FIGURE 13. LOOPBACK TEST AT 120kbps
FIGURE 14. LOOPBACK TEST AT 250kbps
TABLE 4. LOGIC FAMILY COMPATIBILITY WITH VARIOUS
SUPPLY VOLTAGES
SYSTEM
POWER-SUPPLY
VOLTAGE
(V)
V
CC
SUPPLY
VOLTAGE
(V)
COMPATIBILITY
3.3
3.3
Compatible with all CMOS
families.
5
5
Compatible with all TTL and
CMOS logic families.
5
3.3
Compatible with ACT and HCT
CMOS, and with TTL. ICL32XX
outputs are incompatible with AC,
HC, and CD4000 CMOS inputs.
T1
IN
T1
OUT
R1
OUT
5
μ
s/DIV.
V
CC
= +3.3V
C1 - C4 = 0.1
μ
F
5V/DIV.
T1
IN
T1
OUT
R1
OUT
2
μ
s/DIV.
5V/DIV.
V
CC
= +3.3V
C1 - C4 = 0.1
μ
F
ICL3224E, ICL3226E, ICL3244E
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3244ECAZ-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| ICL3226E | ±15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transceivers with Enhanced Automatic Powerdown(±15kV ESD 防護, +3V至+5.5V, 1微安, 250kbps, RS-232收發器，具有增強型自動關斷功能) |
| ICL3224E | ±15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transceivers with Enhanced Automatic Powerdown(±15kV ESD 防護, +3V至+5.5V, 1微安, 250kbps, RS-232收發器，具有增強型自動關斷功能) |
| ICL3244E | ±15kV ESD Protected, +3V to +5.5V, 1Microamp, 250kbps, RS-232 Transceivers with Enhanced Automatic Powerdown(±15kV ESD 防護, +3V至+5.5V, 1微安, 250kbps, RS-232收發器，具有增強型自動關斷功能) |
| ICL3232ECB-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL3244EIR | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述: |
| ICL3244EIV | 制造商:Rochester Electronics LLC 功能描述:RS232 3V 3D/5R 15KV E-DWN 28TSSOP IND - Bulk 制造商:Intersil Corporation 功能描述: |
| ICL3244IA | 功能描述:IC 3DRVR/5RCVR RS232 3V 28-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ICL3244IA-T | 功能描述:IC 3DRVR/5RCVR RS232 3V 28-SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:25 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:4.5 V ~ 5.5 V 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 供應商設備封裝:16-PDIP 包裝:管件 |
| ICL3244IB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。