參數資料
型號： HY27SF161G2M-VES
廠商： Hynix Semiconductor Inc.
英文描述： 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
中文描述： 1Gbit的（128Mx8bit / 64Mx16bit）NAND閃存
文件頁數： 8/48頁
文件大?。?/td> 476K
代理商： HY27SF161G2M-VES
Rev 0.7 / Apr. 2005
8
Preliminary
HY27UF(08/ 16)1G2M Series
HY27SF(08/ 16)1G2M Series
1Gbit (128Mx8bit / 64Mx16bit) NAND Flash
1
.2 PIN DESCRIPTION
Pin Name
Description
IO0-IO7
IO8-IO15(1)
DATA INPUTS/ OUTPUTS
The IO pins allow to input command, address and data and to output data during read / program
operations. The inputs are latched on the rising edge of Write Enable (WE#). The I/O buffer float to
High-Z when the device is deselected or the outputs are disabled.
CLE
COMMAND LATCH ENABLE
This input activates the latching of the IO inputs inside the Command Register on the Rising edge of
Write Enable (WE#).
ALE
ADDRESS LATCH ENABLE
This input activates the latching of the IO inputs inside the Address Register on the Rising edge of
Write Enable (WE#).
CE#
CHIP ENABLE
This input controls the selection of the device. When the device is busy CE# low does not deselect
the memory.
WE#
WRITE ENABLE
This input acts as clock to latch Command, Address and Data. The IO inputs are latched on the rise
edge of WE#.
RE#
READ ENABLE
The RE# input is the serial data-out control, and when active drives the data onto the I/O bus. Data
is valid tREA after the falling edge of RE# which also increments the internal column address counter
by one.
WP#
WRITE PROTECT
The WP# pin, when Low, provides an Hardware protection against undesired modify (program /
erase) operations.
RB#
READY BUSY
The Ready/Busy output is an Open Drain pin that signals the state of the memory.
VCC
SUPPLY VOLTAGE
The VCC supplies the power for all the operations (Read, Write, Erase).
VSS
GROUND
NC
NOT CONNECTED
PRE
To Enable Power On Auto Read. When PRE is a logic high, Power on Auto Read mode is enabled, and
when PRE is a logic low, Power Auto Read mode is disabled. Power On Auto Read mode is available
only on 3.3V device.
Not using POWER-ON AUTO-READ, connect it Vss or leave it N.C.
Table 2: Pin Description
NOTE:
1. For x16 version only
2. A 0.1uF capacitor should be connected between the VCC Supply Voltage pin and the VSS Ground pin to decouple
the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required
during program and erase operations.
相關PDF資料
PDF描述
HY27SF161G2M-VIB 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27SF161G2M-VIP 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UF161G2M-TIB 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UF161G2M-TIP 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27UF161G2M-TIS 1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
相關代理商/技術參數
參數描述
HY27SF161G2M-VIB 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27SF161G2M-VIP 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27SF161G2M-VIS 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27SF161G2M-VMB 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
HY27SF161G2M-VMP 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:1Gbit (128Mx8bit / 64Mx16bit) NAND Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*