- 您現在的位置：買賣IC網 > PDF目錄384455 > HV830 (ELAN Microelctronics Corp .) High-Voltage EL Lamp Driver(輸入電壓2.0-9.5V,高壓電致反光燈驅動器) PDF資料下載
參數資料
| 型號： | HV830 |
| 廠商： | ELAN Microelctronics Corp . |
| 英文描述： | High-Voltage EL Lamp Driver(輸入電壓2.0-9.5V,高壓電致反光燈驅動器) |
| 中文描述： | 高電壓發光燈驅動器（輸入電壓2.0 - 9.5V的，高壓電致反光燈驅動器） |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 53K |
| 代理商： | HV830 |
3
HV830
Figure 1: Test Circuit, V
IN
= 3.0V
1
7
2
3
4
8
6
5
V
IN
= 3.0V
ON = V
DD
OFF = 0V
0.01
μ
F
200V
0.1
μ
F
2
220
μ
H
1
BAS21LT1
1M
3.3M
2.0K
10nF
Equivalent to 3 square inch lamp.
HV830
L
x
GND
V
B
V
A
R
EL-osc
V
DD
R
SW-osc
C
s
1nF
Notes:
1. Murata part # LQH4N221K04 (DC resistance < 5.4
)
2. Larger values may be required depending upon supply impedance.
For additional information, see Application Notes AN-H33 and AN-H34.
Enable/Disable Configuration
The HV830 can be easily enabled and disabled via a logic control
signal on the R
SW
and R
EL
resistors as shown in Figure 2 below.
The control signal can be from a microprocessor. R
SW
and R
EL
are typically very high values. Therefore, only 10
’
s of microam-
1
7
2
3
4
8
6
5
V
DD
ON =V
DD
OFF = 0V
C
S
200V
4.7
μ
F
15V
1nF
L
x
BAS21LT1
R
SW
R
EL
EL Lamp
HV830LG
L
x
GND
V
B
V
A
R
EL-osc
V
DD
R
SW-osc
C
s
+
-
Remote
Enable
Figure 2: Enable/Disable Configuration
peres will be drawn from the logic signal when it is at a logic high
(enable) state. When the microprocessor signal is high the
device is enabled and when the signal is low, it is disabled.
Split Supply Configuration Using a Single
Cell (1.5V) Battery
The HV830 can also be used for handheld devices operating
from a single cell 1.5V battery where a regulated voltage is
available. This is shown in Figure 3. The regulated voltage can
be used to run the internal logic of the HV830. The amount of
current necessary to run the internal logic is typically 100
μ
A
at a V
DD
of 3.0V. Therefore, the regulated voltage could easily
provide the current without being loaded down. The HV830
used in this configuration can also be enabled/disabled via
logic control signal on the R
SW
and R
EL
resistors as shown in
Figure 2.
Split Supply Configuration for Battery
Voltages of Higher than 9.5V
Figure 3 can also be used with high battery voltages such as 12V
as long as the input voltage, V
DD
, to the HV830 device is within
its specifications of 2.0V to 9.5V.
相關PDF資料 |
PDF描述 |
|---|---|
| HV832MG | Dual High Voltage, Low Noise EL Lamp Driver |
| HV832 | Dual High Voltage, Low Noise EL Lamp Driver(高電壓,低噪雙路EL燈驅動器) |
| HV832X | Dual High Voltage, Low Noise EL Lamp Driver |
| HV832 | Dual High Voltage, Low Noise EL Lamp Driver |
| HV832DB1 | Dual EL Lamp Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV830_07 | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:High Voltage EL Lamp Driver IC |
| HV8308DJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| HV8308PJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| HV8308X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Interface IC |
| HV830DB1 | 功能描述:電源管理IC開發工具 HV830 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。