- 您現在的位置：買賣IC網 > PDF目錄384455 > HV823 (Supertex, Inc.) High Voltage EL Lamp Driver PDF資料下載
參數資料
| 型號： | HV823 |
| 廠商： | Supertex, Inc. |
| 英文描述： | High Voltage EL Lamp Driver |
| 中文描述： | 高壓EL燈驅動器 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 391K |
| 代理商： | HV823 |
7
HV823
External Component Description
External Component
Selection Guide Line
Diode
Fast reverse recovery diode, 1N4148 or equivalent.
Cs Capacitor
0.01
μ
F to 0.1
μ
F, 100V capacitor to GND is used to store the energy transferred from the inductor.
R
EL-osc
The EL lamp frequency is controlled via an external R
EL
resistor connected between R
EL-osc
and V
DD
of the
device. The lamp frequency increases as R
EL
decreases. As the EL lamp frequency increases, the amount
of current drawn from the battery will increase and the output voltage V
CS
will decrease. The color of the EL
lamp is dependent upon its frequency.
A 2M
resistor would provide lamp frequency of 330 to 450Hz. Decreasing the R
EL-osc
by a factor of 2 will
increase the lamp frequency by a factor of 2.
R
SW-osc
The switching frequency of the converter is controlled via an external resistor, R
SW
between R
SW-osc
and V
DD
of the device. The switching frequency increases as R
SW
decreases. With a given inductor, as the switching
frequency increases, the amount of current drawn from the battery will decrease and the output voltage, V
CS
,
will also decrease.
C
SW
Capacitor
A 1nF capacitor is recommended on R
SW-osc
to GND when a 0.01
μ
F C
S
capacitor is used. This capacitor
is used to shunt any switching noise that may couple into the R
SW-osc
pin. The C
SW
capacitor may also be
needed when driving large EL lamp due to increase in switching noise.
Lx Inductor
The inductor L
x
is used to boost the low input voltage by inductive flyback. When the internal switch is on,
the inductor is being charged. When the internal switch is off, the charge stored in the inductor will be
transferred to the high voltage capacitor C
S
. The energy stored in the capacitor is connected to the internal
H-bridge and therefore to the EL lamp. In general, smaller value inductors, which can handle more current,
are more suitable to drive larger size lamps. As the inductor value decreases, the switching frequency of the
inductor (controlled by R
SW
) should be increased to avoid saturation.
560
μ
H Murata inductors with 14.5
series DC resistance is typically recommended. For inductors with the
same inductance value but with lower series DC resistance, lower R
SW
value is needed to prevent high current
draw and inductor saturation.
Lamp
As the EL lamp size increases, more current will be drawn from the battery to maintain high voltage across
the EL lamp. The input power, (V
IN
x I
IN
), will also increase. If the input power is greater than the power
dissipation of the package (400mW), an external resistor in series with one side of the lamp is recommended
to help reduce the package power dissipation.
Enable/Disable Configuration
The HV823 can be easily enabled and disabled via a logic control
signal on the R
SW
and R
EL
resistors as shown in Figure 4 below.
The control signal can be from a microprocessor. R
SW
and R
EL
are typically very high values. Therefore, only 10
’
s of microam-
Figure 4: Enable/Disable Configuration
peres will be drawn from the logic signal when it is at a logic high
(enable) state. When the microprocessor signal is high the
device is enabled and when the signal is low, it is disabled.
1
7
2
3
4
8
6
5
V
IN
= V
DD
ON =V
DD
OFF = 0V
C
S
100V
4.7
μ
F
15V
1nF
L
x
1N4148
R
SW
R
EL
EL Lamp
HV823LG
L
x
GND
V
B
V
A
R
EL-osc
V
DD
R
SW-osc
C
s
+
-
Remote
Enable
相關PDF資料 |
PDF描述 |
|---|---|
| HV823LG | High Voltage EL Lamp Driver |
| HV823X | High Voltage EL Lamp Driver |
| HV824 | High-Voltage EL Lamp Driver(輸入電壓1.0-1.6V,高壓電致反光燈驅動器) |
| HV825 | High-Voltage EL Lamp Driver(輸入電壓1.0-1.6V,高壓電致反光燈驅動器) |
| HV825 | High Voltage EL Lamp Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HV823DB1 | 功能描述:電源管理IC開發工具 HV823 Demo Brd RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| HV823LG | 功能描述:顯示驅動器和控制器 EL LAMP DRIVER RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| HV823LG FAB | 制造商:Supertex Inc 功能描述: |
| HV823LG-G | 功能描述:顯示驅動器和控制器 NVCMOS RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| HV823X | 制造商:SUPERTEX 制造商全稱:SUPERTEX 功能描述:High Voltage EL Lamp Driver |
發布緊急采購，3分鐘左右您將得到回復。