- 您現在的位置：買賣IC網 > PDF目錄370715 > HT7610A(16DIP) Motion/Proximity Detector PDF資料下載
參數資料
| 型號： | HT7610A(16DIP) |
| 英文描述： | Motion/Proximity Detector |
| 中文描述： | 運動/接近探測器 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 165K |
| 代理商： | HT7610A(16DIP) |
HT761X
Rev. 1.10
6
September 18, 2002
Options for setting the comparator window to be
1
1
11.3
or
1
DD
V
EE
).
1
DD
V
EE
).
The default is
PIR amplifier
Consult the diagram below for details on the PIR front
end amplifier.
In the Fig.2 below there are 2 op-amps with different ap-
plications. OP1 can be used independently as a first
stage inverting or non-inverting amplifier for the PIR.
As the output of OP2 is directly connected to the input of
the comparator, it is used as a second stage amplifying
device. The non-inverting input of OP2 is connected to
the comparator s window center point and can be used
to check this voltage and to provide a bias voltage that is
equal to the center point voltage of the comparator. In
Fig.2 the comparator can have 3 window levels set by
1
DD
V
EE
), 2.
3.1
9(V
DD
V
EE
).
mask option. 1.
11
DD
-V
EE
),
If the window level fails to be specified the default win-
1
(V
DD
V
EE
). The preset voltage of
dow is set to
16
V
DD
V
EE
is 4V. The default values of V
CP
and V
CN
are
4
therefore 0.25V, (
)
Second stage amplifier
Usually the second stage PIR amplifier is a simple ca-
pacitively coupled inverting amplifier with a low pass
configuration. The noninverting input terminal is biased
to the center point of the comparator window and the
output of the second stage amplifier is directly coupled
to the comparator center point.
In Fig.3 OP2P is directly connected to the comparator
window center, and with the C3 filter it can act as the
bias for OP2. For this configuration A
V
=R2, low cutoff
frequency f
L
=
2 1
f
H
=
1
R2C2
2
. By changing the value of R2 the sensitivity
can be varied. C1 and C3 should be of low leakage
types to prevent the DC operating point from changing
due to current leakage.
Each op-amp current consumption is approximately
5 A with the op-amps and comparator s working volt-
age all provided by the regulator.
Consult the following diagrams for typical PIR front end
circuit.
First stage of PIR amplifier
Fig.4 shows a typical first stage amplifier. C2 and R2
form a simple low pass filter with cut off frequency at
7Hz. The low frequency response is governed by R1
and C1 with cut-off frequency at 0.33Hz.
A
V
=( R1+ R2 )
1
*
$
% &
$
$
Fig.2 PIR amplifier
3
; ! $ 0 ) 0
* & *
2
:
2
2
Fig.3 Typical second stage amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| HT7610A(16SOIC) | Motion/Proximity Detector |
| HT7610B | General Purpose PIR Controller |
| HT7610B(16DIP) | Motion/Proximity Detector |
| HT7610B(16SOIC) | Motion/Proximity Detector |
| HT7611A | General Purpose PIR Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HT7610B | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:General Purpose PIR Controller |
| HT7610B(16DIP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Motion/Proximity Detector |
| HT7610B(16SOIC) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Motion/Proximity Detector |
| HT7611 | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:General Purpose PIR Controller |
| HT7611A | 制造商:HOLTEK 制造商全稱:Holtek Semiconductor Inc 功能描述:General Purpose PIR Controller |
發布緊急采購，3分鐘左右您將得到回復。