- 您現在的位置：買賣IC網 > PDF目錄385394 > HSDL-3211-021 (Avago Technologies Ltd.) IrDA㈢ Data Compliant Low Power 1.15 Mbit/s Infrared Transceiver PDF資料下載
參數資料
| 型號： | HSDL-3211-021 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | IrDA㈢ Data Compliant Low Power 1.15 Mbit/s Infrared Transceiver |
| 中文描述： | 紅外線㈢數據兼容低功耗1.15 Mbit / s的紅外收發器 |
| 文件頁數： | 2/18頁 |
| 文件大?。?/td> | 184K |
| 代理商： | HSDL-3211-021 |
2
Order Information
Part Number
Packaging Type
Package
Quantity
HSDL-3211-021
Tape and Reel
Front View
2500
I/O Pins Configuration Table
Pin
Symbol
Description
I/O Type
Notes
1
LED A
LED Anode
I
1
2
LED C
LED Cathode
2
3
TXD
Transmit Data. Active High.
I
3
4
RXD
Receive Data. Active Low.
O
4
5
SD
Shutdown. Active High.
I
5
6
Vcc
Supply Voltage
6
7
IOVcc
Input/Output ASIC Vcc
7
8
GND
Ground
8
-
Shield
EMI Shield
9
Marking Information
The unit is marked with ‘
yyww
’
on the shield:
yy
= year
ww
= work week
Recommended Application Circuit Components
Component
Recommended Value
Notes
R1
3.9
±
5%, 0.25 watt for 2.4
≤
Vled<2.7V
5.6
±
5%, 0.25 watt for 2.7
≤
Vled<3.3V
10
±
5%, 0.25 watt for 3.3
≤
Vled<4.2V
15
±
5%, 0.25 watt for 4.2
≤
Vled<5.5V
0.47
μ
F
±
20%, X7R Ceramic
6.8
μ
F
±
20%, Tantalum
CX1, CX4
10
CX2, CX3
11
Notes:
1. Tied through external series resistor, R1, to regulated Vled from 2.4 to 5.5V. Please refer to table
below for recommended series resistor value.
2. Internally connected to LED driver. Leave this pin unconnected.
3. This pin is used to transmit serial data when SD pin is low. If this pin is held high for longer than
50 ms, the LED is turned off. Do NOT float this pin.
4. This pin is capable of driving a standard CMOS or TTL load. No external pull-up or pull-down
resistor is required. The pin is in tri-state when the transceiver is in shutdown mode. The receiver
output echoes transmitted signal.
5. The transceiver is in shutdown mode if this pin is high. Do NOT float this pin.
6. Regulated, 2.4 to 3.6 Volts.
7. Connect to ASIC logic controller Vcc voltage or supply voltage. The voltage at this pin must be
equal to or less than supply voltage.
8. Connect to system ground.
9. Connect to system ground via a low inductance trace. For best performance, do not connect
directly to the transceiver pin GND
10. CX1 must be placed within 0.7 cm of the HSDL-3211 to obtain optimum noise immunity.
11. In environments with noisy power supplies, including CX2, as shown in Figure 1, can enhance
supply ripple rejection performance.
Application Support Information
The Application Engineering
Group is available to assist you
with the application design
associated with the HSDL-3211
infrared transceiver module. You
can contact them through your
local sales representatives for
additional details.
相關PDF資料 |
PDF描述 |
|---|---|
| HSDL-3220 | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s Infrared Transceiver |
| HSDL-3220-001 | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s Infrared Transceiver |
| HSDL-3220-021 | IrDA㈢ Data Compliant Low Power 4.0 Mbit/s Infrared Transceiver |
| HSDL-3602 | IrDA㈢ Data 1.4 Compliant 4 Mb/s 3V Infrared Transceiver |
| HSDL-3602-008 | IrDA㈢ Data 1.4 Compliant 4 Mb/s 3V Infrared Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HSDL-3220 | 制造商:Avago Technologies 功能描述:TRANSCEIVER IRDA 4MB/S |
| HSDL-3220-001 | 制造商:AVAGO 制造商全稱:AVAGO TECHNOLOGIES LIMITED 功能描述:IrDA㈢ Data Compliant Low Power 4.0 Mbit/s Infrared Transceiver |
| HSDL-3220-021 | 功能描述:紅外收發器 20-30cm 3V FIR RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel |
| HSDL-3310 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IrDA 1.3 Data Compliant 1.15Mb/s 3-5V Infrared Transceiver |
| HSDL-3310#007 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
發布緊急采購，3分鐘左右您將得到回復。