參數資料
型號: HPL1117-28G
廠商: Electronic Theatre Controls, Inc.
英文描述: 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
中文描述: 1A低壓差快速反應積極可調穩壓器和固定在1.8V,2.5V,工作在2.85V,3.3V和5V
文件頁數: 10/19頁
文件大小: 204K
代理商: HPL1117-28G
Rev. B.13 - Mar., 2004
HPL1117
10
Copyright
HIPAC Semiconductor, Inc.
www.hipacsemi.com
The HPL1117 requires an output capacitor to maintain
stability and improve transient response. Proper ca-
pacitor selection is important to ensure proper
operation. The HPL1117 output capacitor selection is
dependent upon the ESR (equivalent series resistance)
of the output capacitor to maintain stability. When the
output capacitor is 10uF or greater, the output capaci-
tor should have an ESR less than 1
.
This will improve
transient response as well as promote stability. A low-
ESR solid tantalum capacitor works extremely well
and provides good transient response and stability over
temperature.
V
IN
HPL1117
IN
ADJ
OUT
R1
R2
Rp
PARASITIC
LINE RESISTANCE
CONNECT
R1 TO CASE
CONNECT
R2 TO LOAD
R
L
Output Voltage
V
IN
HPL1117
IN
ADJ
OUT
V
REF
R1
R2
V
OUT
I
ADJ
60
μ
A
Application Information
Input Capac itor
Output Capac itor
The HPL1117 develops a 1.25V reference voltage be-
tween the output and the adjust terminal. By placing
a resistor between these two terminals, a constant
Current is caused to flow through R1 and down through
R2 to set the overall output voltage. Normally this
current is chosen to be the specified minimum load
current of 10mA. For fixed voltage devices R1 and R2
are included in the device.
Load Regulation
When the adjustable regulator is used. Load regula-
tion will be limited by the resistance of the wire con-
necting the regulator to the load. The data sheet speci-
fication for load regulation is measured at the output
pin of the device. Best load regulation is obtained
when the top of the resistor divider (R1) is tied di-
rectly to the output pin of the device, not to the load.
For fixed voltage devices the top of R1 is internally
connected to the output, and the ground pin can be
connected to low side of the load. If R1 were con-
nected to the load, RP is multiplied by the divider
ratio, the effective resistance between the regulator
and the load would be:
An input capacitor of 10
μ
F or greater is
recommended. Tantalum, or aluminum electrolytic
capacitors can be used for bypassing. Larger Val-
ues will improve ripple rejection by bypassing the in-
put to the regulator.
V
OUT
= V
REF
(1+R1
ADJ
R2
Figure 1. Basic Adjustable Regulator
Figure 2. Connections for Best Load Regulation
Rp X (1+R2
相關PDF資料
PDF描述
HPL1117-28U 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-28V 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33F 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33G 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33U 1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
相關代理商/技術參數
參數描述
HPL1117-28U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-28V 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33F 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V
HPL1117-33U 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1A Low Dropout Fast Response Positive Adjustable Regulator and Fixed 1.8V, 2.5V, 2.85V, 3.3V and 5V