- 您現在的位置：買賣IC網 > PDF目錄370661 > HPC3130PGELOW-PROFILEQUAD (Texas Instruments, Inc.) PCI HOT PLUG CONTROLLER PDF資料下載
參數資料
| 型號： | HPC3130PGELOW-PROFILEQUAD |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | PCI HOT PLUG CONTROLLER |
| 中文描述： | 的PCI熱插拔控制器 |
| 文件頁數： | 17/40頁 |
| 文件大?。?/td> | 555K |
| 代理商： | HPC3130PGELOW-PROFILEQUAD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
HPC3130
PCI HOT PLUG CONTROLLER
SCPS029B – DECEMBER1998
17
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
SDA
SCL
Start Condition
Stop Condition
Change of
Data Allowed
Data Line Stable, Data Valid
Figure 2. Serial Bus Start/Stop Conditions and Bit Transfers
Data is transferred on the bus in 8-bit bytes. The number of bytes that can be transmitted during a data transfer
is unlimited; however, each byte must be completed with an acknowledge bit. An acknowledge (ACK) is
indicated by the receiver pulling down the SDA signal so that it remains low during the high state of the SCL
signal as shown in Figure 3.
SCL From
Master
1
2
3
7
8
9
SDA Output
By Transmitter
SDA Output
By Receiver
Figure 3. Serial Bus Protocol – Acknowledge
The HPC3130 serial bus slave interface protocol for write transactions is illustrated in Figure 4. The R/W
command bit is set to zero to indicate a write transaction. For a write operation, the HPC3130 requires a word
address field after the slave address. This address field is comprised of eight bits. Upon receipt of the word
address, the HPC3130 responds with an acknowledge, and waits for the next eight bits of data, again
responding with an acknowledge. After all the data bytes are transferred, the master then terminates the transfer
by generating a STOP condition. The device automatically increments the address for subsequent data words.
After the receipt of each word, the low order address bits are internally incremented by one.
S
b6
b4
b5
b3 b2
b1 b0
0
b7 b6 b5 b4 b3
b2 b1
b0
A
A
Slave Address
Word Address
R/W
S/P = Start/stop condition
A = Slave acknowledgment
b7 b6
b4
b5
b3
b2 b1 b0
A
P
Data Byte
Figure 4. Serial Bus Protocol – Byte Write
A byte read operation is illustrated below. The read protocol is very similar to the write protocol, except the R/W
command bit must be set to one to indicate a read data transfer. First the master issues a write command that
includes the START condition and the slave address field (with the R/W bit set to write), followed by the address
of the word it is to read. This procedure sets the internal address counter of the HPC3130 to the desired address.
After the word address acknowledgment is received by the master, the master immediately reissues a START
condition followed by another slave address field with the R/W bit set to read. The HPC3130 responds with an
acknowledgment and transmits the eight data bits stored in the addressed location. If the master responds with
相關PDF資料 |
PDF描述 |
|---|---|
| HPC3130PBMQUADFLAT | PCI HOT PLUG CONTROLLER |
| HPC3130PBKLOW-PROFILEQUAD | PCI HOT PLUG CONTROLLER |
| HPC43100VHG30 | 16-Bit Microcontroller |
| HPC46003E20 | 16-Bit Microcontroller |
| HPC46003L20 | 16-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPC36003 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High-Performance microControllers |
| HPC36003E30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC36003L30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC36003T30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
| HPC36003V20 | 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。