- 您現在的位置：買賣IC網 > PDF目錄383073 > HMC1021Z Magnetoresistive Sensor PDF資料下載
參數資料
| 型號： | HMC1021Z |
| 英文描述： | Magnetoresistive Sensor |
| 中文描述： | 磁阻傳感器 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 190K |
| 代理商： | HMC1021Z |
HMC10XX FAMILY
10
Figure 9—Single Clock Set/Reset Circuit(1001/1002)
S/R strap @ 4.5
typ.
3A peak (min.)
10K
1
0.22μF
4.7μF (1)
+16 to 20V
17
HMC2003
Clock
S/R
(1) Tantalum, low R
0.022μF
0.022μF
10K
ZTX605
ZTX705
S/R strap @ 4.5
typ.
3A peak (min.)
10K
1
0.22μF
+16 to 20V
17
HMC2003
Clock
S/R
0.022μF
100K
ZTX605
Clock
S/R
-16V
T
PW
≈
2 μsec
5V
reset
Figure 10—Single Clock Reset Only Circuit (1001/1002)
Low Field Measurements—When measuring 100
μ
gauss
resolution or less, the permalloy film must be completely set,
or reset, to insure low noise and repeatable measurements.
A current pulse of 4 amps, or more, for just a couple
microseconds will ensure this. The circuits in Figures 7 and
8 are recommended for applications that require low noise
and high sensitivity magnetic readings.
Low Cost—For minimum field measurements above 500
μ
gauss, a less elaborate pulsing circuit can be used. In both
Figures 9 and 10, the pulse signal is switched using lower cost
Darlington transistors and fewer components. This circuit
may have a more limited temperature range depending on
the quality of transistors selected. If accuracy is not an issue
and cost is, then the reset only circuit in Figure 10 will work.
The circuit in Figure 12 generates a strong set/reset pulse
under a microprocessor clock driven control. A free running
555 timer can also be used to clock the circuit. The SET
current pulse is drawn from the 4.7
μ
F capacitor and a 200
ohm dropping resistor should be placed in series with the
supply to reduce noise.
Figure 11—5V Circuit for SET/RESET (1021/1022)
10K
0.1μF
1μF (1)
+5V
Clock
(1) Tantalum, low R
0.1μF
0.1μF
10K
FMMT617
FMMT717
200
9,15
14
HMC1022
8
For any magnetic sensor application, if temperature drift is
not an issue, then the reset pulse need only be occasionally
applied. This will save power and enable the use of digital
filtering techniques as shown in Figure 11. Circumstances
for a reset pulse would be 1) power on or, 2) field over/
under range condition. Any other time the sensor should
perform normally.
相關PDF資料 |
PDF描述 |
|---|---|
| HMC1022 | Magnetoresistive Sensor |
| HMC103 | SPST RF Absorptive Switch |
| HMC104 | SPDT RF Absorptive Switch |
| HMC105 | SPST RF Absorptive Switch |
| HMC106 | SPDT RF Reflective Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC1021Z RC | 制造商:Honeywell Sensing and Control 功能描述: |
| HMC1021Z-RC | 功能描述:SENSOR LINEAR MAGN 1 AXIS 8-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| HMC1022 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs pHEMT MMIC |
| HMC1022_12 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs pHEMT MMIC |
| HMC1022-TR | 功能描述:SENSOR LINEAR MAGN 2 AXIS 16SOIC RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。