- 您現在的位置：買賣IC網 > PDF目錄384429 > HLMP-HB55 (Avago Technologies Ltd.) 5 mm Precision Optical Performance InGaN Oval LED Lamps PDF資料下載
參數資料
| 型號： | HLMP-HB55 |
| 廠商： | Avago Technologies Ltd. |
| 英文描述： | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
| 中文描述： | 5毫米精密光學性能的InGaN橢圓形發光二極管 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 111K |
| 代理商： | HLMP-HB55 |
9
Precautions:
Lead Forming
The leads of an LED lamp may be preformed or cut to
length prior to insertion and soldering into PC board.
If lead forming is required before soldering, care must
be taken to avoid any excessive mechanical stress
induced to LED package. Otherwise, cut the leads of
LED to length after soldering process at room
temperature. The solder joint formed will absorb the
mechanical stress of the lead cutting from traveling to
the LED chip die attach and wirebond.
For better control, it is recommended to use proper
tool to precisely form and cut the leads to applicable
length rather than doing it manually.
Soldering Conditions
Care must be taken during PCB assembly and soldering
process to prevent damage to LED component.
The closest LED is allowed to solder on board is 1.59 mm
below the body (encapsulant epoxy) for those parts
without standoff.
Recommended soldering conditions:
Wave soldering parameter must be set and maintained
according to recommended temperature and dwell
time in the solder wave. Customer is advised to
periodically check on the soldering profile to ensure the
soldering profile used is always conforming to
recommended soldering condition.
Notes:
1. PCB with different size and design (component density)
will have different heat mass (heat capacity). This might
cause a change in temperature experienced by the board if
same wave soldering setting is used. So, it is recommended
to recalibrate the soldering profile again before loading a
new type of PCB.
2. Avago Technologies' high brightness LED are using high
efficiency LED die with single wire bond as shown below.
Customer is advised to take extra precaution during wave
soldering to ensure that the maximum wave temperature
is not exceeding 250
°
C. Overstressing the LED during
soldering process might cause premature failure to the LED
due to delamination.
Manual Solder
Dipping
–
–
260
°
C Max.
5 sec Max.
Wave Soldering
105
°
C Max.
30 sec Max.
250
°
C Max.
3 sec Max.
Pre-heat Temperature
Pre-heat Time
Peak Temperature
Dwell Time
Relative Light Output vs. J unction Temperature
0
-40
1.0
R
(
J
°
C
T
J
– JUNCTION TEMPERATURE –
°
C
1.2
0.8
-20
0
20
40
60
80
0.2
0.4
0.6
GREEN
BLUE
相關PDF資料 |
PDF描述 |
|---|---|
| HLMP-HB55-HJCxx | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
| HLMP-HB55-JKCxx | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
| HLMP-HM54 | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
| HLMP-HM55 | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
| HLMP-HM55-MQ0xx | 5 mm Precision Optical Performance InGaN Oval LED Lamps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HLMP-HB55-FJ000 | 功能描述:標準LED-通孔 Lamp 5mm InGaN Blue 40X100deg RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| HLMP-HB55-FJ0DD | 功能描述:標準LED-通孔 Lamp 5mm InGaN Blue 40X100deg RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| HLMP-HB55-HJCDD | 功能描述:標準LED-通孔 Lamp 5mm InGaN Blue 40X100deg RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| HLMP-HB55-JKCDD | 功能描述:標準LED-通孔 Blue 40x100deg 40X100deg RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| HLMP-HB56-LP0DD | 功能描述:標準LED-通孔 Blue 40x100deg 40X100deg RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。