- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9011 (Intersil Corporation) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9011 |
| 廠商： | Intersil Corporation |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | 發動機爆震信號處理器 |
| 文件頁數： | 10/11頁 |
| 文件大小： | 76K |
| 代理商： | HIP9011 |
4-10
The Digital SPI Block diagram in Figure 5 shows the
programming flow of the chip. An eight bit word is received at
the SI port. Data is shifted in by the SCK clock when the chip
is enable by the CS pin. The word is decoded by the address
decoding circuit, and the information is directed to one of 5
registers. These registers control the following chip functions:
1. Band Pass Filter frequency.
2. Gain control or attenuation.
3. Integration time constant of the rectified BPF output.
4. Prescaler.
5. Test/Channel Select.
a) Test conditions of the part.
b) Channel select to one of two input amplifiers.
A crystal oscillator circuit is provided. The chip requires at
minimum a 4MHz crystal to be connected across OSCIN
and OSCOUT pins. An external 4MHz signal may also be
provided to the OSCIN Terminal Pin 9.
In the diagnostic mode, we can use the digital multiplexer to
output one of the following results through the SO pin (11):
1. Value of one of the five registers in the chip
2. Buffered value of the SI pin (12).
3. Value of an internal comparator used to rectify the analog
signal
A digital SPI filter is located in the SPI Block which provides
a pseudo noise immunity characteristic.
The digital SPI filter operation requires that the SCK be low
prior to the fall of CS, followed by 8 SCK pulses (low-high-
low transitions). With the SCK ending the pulse sequence in
a logic low condition, the transition of CS from a low to high
transition will cause the data-word in the SPI Buffer to be
loaded into the proper addressed programmable register.
During the Integration mode, INT/HOLD pin is high, any
single SPI byte that is entered will be acted upon if the
conditions of the digital SPI filter are met. The digital SPI
filter allows for only 8 bits per word to be accepted.
S
SCK
CS
ADDRESS DECODER
PRESCALER/SO TERMINAL STATUS
GAIN CONTROL
INTEGRATOR TIME CONSTANT
TEST/CHANNEL SELECT CONTROL
COMP OUT
SO
SI
D
BANDPASS FILTER
FIGURE 5. PROGRAMMABLE REGISTERS AND STATE MACHINE
SI
TEST
HIP9011
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9011AB | Engine Knock Signal Processor |
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AP | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9021 | Portable Battery Drive/Torque Controller for N-Channel MOSFETs in Motor Control Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011AB | 功能描述:IC SENSOR ENGINE KNOCK 20-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| HIP9011ABR4682 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745A | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。