- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP6603A (Intersil Corporation) Synchronous-Rectified Buck MOSFET Drivers(同步整流的MOSFET驅動器) PDF資料下載
參數資料
| 型號： | HIP6603A |
| 廠商： | Intersil Corporation |
| 英文描述： | Synchronous-Rectified Buck MOSFET Drivers(同步整流的MOSFET驅動器) |
| 中文描述： | 同步整流降壓MOSFET驅動器（同步整流的MOSFET的驅動器） |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 101K |
| 代理商： | HIP6603A |
5
A falling transition on PWM indicates the turn-off of the upper
MOSFET and the turn-on of the lower MOSFET. A short
propagation delay [t
PDLUGATE
] is encountered before the
upper gate begins to fall [t
FUGATE
]. Again, the adaptive shoot-
through circuitry determines the lower gate delay time,
t
PDHLGATE
. The PHASE voltage is monitored and the lower
gate is allowed to rise after PHASE drops below 0.5V. The
lower gate then rises [t
RLGATE
], turning on the lower
MOSFET.
Three-State PWM Input
A unique feature of the HIP660X drivers is the addition of a
shutdown window to the PWM input. If the PWM signal
enters and remains within the shutdown window for a set
holdoff time, the output drivers are disabled and both
MOSFET gates are pulled and held low. The shutdown state
is removed when the PWM signal moves outside the
shutdown window. Otherwise, the PWM rising and falling
thresholds outlined in the ELECTRICAL SPECIFICATIONS
determine when the lower and upper gates are enabled.
Adaptive Shoot-Through Protection
Both drivers incorporate adaptive shoot-through protection
to prevent upper and lower MOSFETs from conducting
simultaneously and shorting the input supply. This is
accomplished by ensuring the falling gate has turned off one
MOSFET before the other is allowed to rise.
During turn-off of the lower MOSFET, the LGATE voltage is
monitored until it reaches a 2.2V threshold, at which time the
UGATE is released to rise. Adaptive shoot-through circuitry
monitors the PHASE voltage during UGATE turn-off. Once
PHASE has dropped below a threshold of 0.5V, the LGATE
is allowed to rise. PHASE continues to be monitored during
the lower gate rise time. If PHASE has not dropped below
0.5V within 250ns, LGATE is taken high to keep the
bootstrap capacitor charged. If the PHASE voltage exceeds
the 0.5V threshold during this period and remains high for
longer than 2
μ
s, the LGATE transitions low. Both upper and
lower gates are then held low until the next rising edge of the
PWM signal.
Power-On Reset (POR) Function
During initial startup, the VCC voltage rise is monitored and
gate drives are held low until a typical VCC rising threshold
of 9.95V is reached. Once the rising VCC threshold is
exceeded, the PWM input signal takes control of the gate
drives. If VCC drops below a typical VCC falling threshold of
9.2V during operation, then both gate drives are again held
low. This condition persists until the VCC voltage exceeds
the VCC rising threshold.
Internal Bootstrap Device
Both drivers feature an internal bootstrap device. Simply
adding an external capacitor across the BOOT and PHASE
pins completes the bootstrap circuit.
The bootstrap capacitor must have a maximum voltage
rating above VCC + 5V. The bootstrap capacitor can be
chosen from the following equation:
Where Q
GATE
is the amount of gate charge required to fully
charge the gate of the upper MOSFET. The
V
BOOT
term is
defined as the allowable droop in the rail of the upper drive.
As an example, suppose a HUF76139 is chosen as the
upper MOSFET. The gate charge, Q
GATE
, from the data
sheet is 65nC for a 10V upper gate drive. We will assume a
200mV droop in drive voltage over the PWM cycle. We find
that a bootstrap capacitance of at least 0.325
μ
F is required.
The next larger standard value capacitance is 0.33
μ
F.
Gate Drive Voltage Versatility
The HIP6601A and HIP6603A provide the user total
flexibility in choosing the gate drive voltage. The HIP6601A
lower gate drive is fixed to VCC [+12V], but the upper drive
rail can range from 12V down to 5V depending on what
voltage is applied to PVCC. The HIP6603A ties the upper
and lower drive rails together. Simply applying a voltage from
5V up to 12V on PVCC will set both driver rail voltages.
Power Dissipation
Package power dissipation is mainly a function of the
switching frequency and total gate charge of the selected
MOSFETs. Calculating the power dissipation in the driver for
a desired application is critical to ensuring safe operation.
Exceeding the maximum allowable power dissipation level
will push the IC beyond the maximum recommended
operating junction temperature of 125
o
C. The maximum
allowable IC power dissipation for the SO8 package is
approximately 800mW. When designing the driver into an
application, it is recommended that the following calculation
be performed to ensure safe operation at the desired
frequency for the selected MOSFETs. The power dissipated
by the driver is approximated as:
where f
sw
is the switching frequency of the PWM signal. V
U
and V
L
represent the upper and lower gate rail voltage. Q
U
and Q
L
is the upper and lower gate charge determined by
MOSFET selection and any external capacitance added to
the gate pins. The I
DDQ
V
CC
product is the quiescent power
of the driver and is typically 30mW.
The power dissipation approximation is a result of power
transferred to and from the upper and lower gates. But, the
internal bootstrap device also dissipates power on-chip
during the refresh cycle. Expressing this power in terms of
the upper MOSFET total gate charge is explained below.
C
BOOT
Q
BOOT
-----------------------
≥
P
1.05f
sw
3
2
--
V
U
Q
U
V
L
Q
L
+
I
DDQ
V
CC
+
=
HIP6601A, HIP6603A
相關PDF資料 |
PDF描述 |
|---|---|
| HIP7010 | J1850 Byte Level Interface Circuit |
| HIP7010B | J1850 Byte Level Interface Circuit |
| HIP7010P | FPGA 2000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP7020 | FPGA 2000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP7020AB | FPGA 2000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6603ACB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6603ACB-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Synchronous Rectified Buck MOSFET Drivers |
| HIP6603B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Synchronous Rectified Buck MOSFET Drivers |
| HIP6603BCB | 功能描述:IC DRIVER MOSFET SYNC BUCK 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:低端 輸入類型:非反相 延遲時間:40ns 電流 - 峰:9A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:4.5 V ~ 35 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263 包裝:管件 |
| HIP6603BCB-T | 功能描述:IC DRIVER MOSFET SYNC BUCK 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:低端 輸入類型:非反相 延遲時間:40ns 電流 - 峰:9A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:4.5 V ~ 35 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。