參數資料
型號： HIP6303EVAL1
廠商： Intersil Corporation
英文描述： Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
中文描述： 微處理器核心電壓調節器的多相降壓PWM控制器
文件頁數： 13/17頁
文件大?。?/td> 195K
代理商： HIP6303EVAL1
13
The inductor, or load current, flows alternately from V
IN
through Q1 and from ground through Q2. The HIP6303
samples the on-state voltage drop across each Q2 transistor
to indicate the inductor current in that channel. The voltage
drop is sampled 1/3 of a switching period, 1/F
SW
, after Q1 is
turned OFF and Q2 is turned on. Because of the sawtooth
current component, the sampled current is different from the
average current per channel. Neglecting secondary effects,
the sampled current (I
SAMPLE
) can be related to the load
current (I
LT
) by:
I
SAMPLE
=
I
LT
/ n +
(V
IN
V
CORE
- 3V
CORE2
) / (6L x F
SW
x V
IN
)
Where: I
LT
= total load current
n = the number of channels
Example: Using the previously given conditions, and
For I
LT
= 100A,
n = 4
Then I
SAMPLE
= 25.49A.
As discussed previously, the voltage drop across each Q2
transistor at the point in time when current is sampled is
r
DSON
(Q2) x I
SAMPLE
. The voltage at Q2’s drain, the
PHASE node, is applied through the R
ISEN
resistor to the
HIP6303 ISEN pin. This pin is held at virtual ground, so the
current into ISEN is:
I
SENSE
= I
SAMPLE
x r
DS(ON)
(Q2) / R
ISEN
.
R
Isen
= I
SAMPLE
x r
DS(ON)
(Q2) / 50
μ
A
Example: From the previous conditions,
where I
LT
= 100A,
I
SAMPLE
= 25.49A,
r
DS(ON)
(Q2)
= 4m
Then: R
ISEN
= 2.04K and
I
CURRENT TRIP
= 165%
Short circuit I
LT
= 165A.
Channel Frequency Oscillator
The channel oscillator frequency is set by placing a resistor,
R
T
, to ground from the FS/DIS pin. Figure 10 is a curve
showing the relationship between frequency, F
SW,
and
resistor R
T
. To avoid pickup by the FS/DIS pin, it is important
to place this resistor next to the pin. If this pin is also used to
disable the converter, it is also important to locate the pull-
down device next to this pin.
Layout Considerations
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit
and lead to device over-voltage stress. Careful component
layout and printed circuit design minimizes the voltage
spikes in the converter. Consider, as an example, the turnoff
transition of the upper PWM MOSFET. Prior to turnoff, the
upper MOSFET was carrying channel current. During the
turnoff, current stops flowing in the upper MOSFET and is
picked up by the lower MOSFET. Any inductance in the
switched current path generates a large voltage spike during
the switching interval. Careful component selection, tight
layout of the critical components, and short, wide circuit
traces minimize the magnitude of voltage spikes. Contact
Intersil
for evaluation board drawings of the component
placement and printed circuit board.
There are two sets of critical components in a DC-DC
converter using a HIP6303 controller and a HIP6601 gate
driver. The power components are the most critical because
they switch large amounts of energy. Next are small signal
components that connect to sensitive nodes or supply
critical bypassing current and signal coupling.
The power components should be placed first. Locate the
input capacitors close to the power switches. Minimize the
length of the connections between the input capacitors, C
IN
,
and the power switches. Locate the output inductors and
output capacitors between the MOSFETs and the load.
Locate the gate driver close to the MOSFETs.
50
100
10
20
CHANNEL OSCILLATOR FREQUENCY, F
SW
(kHz)
200
500 1,000
5,000 10,000
2,000
1
2
5
10
20
50
100
200
500
1,000
R
T
(
)
FIGURE 10. RESISTANCE R
T
vs FREQUENCY
HIP6303
相關PDF資料
PDF描述
HIP6304CB-T Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6304 Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller(微處理器核心電壓穩壓器多相PWM控制電路)
HIP6304CB 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
HIP6304EVAL1 Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6500B Multiple Linear Power Controller with ACPI Control Interface
相關代理商/技術參數
參數描述
HIP6304 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6304 WAF 制造商:Intersil Corporation 功能描述:
HIP6304CB 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述:
HIP6304CB-T 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Intersil Corporation 功能描述:
HIP6304EVAL1 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*