
2-3
File Number
4029.5
HIP5010, HIP5011
7V 17A SynchroFET Complementary
Drive Synchronous Half-Bridge
Designed with the P6 and Pentium in mind, the Intersil
SynchroFET family provides a new approach for
implementing a synchronous rectified buck switching regulator.
The SynchroFET replaces two power DMOSs, a Schottky
diode, two gate drivers and synchronous control circuitry. The
complementary drive circuit turns the upper FET on and the
lower FET off when the input from the PWM is high. When the
input from the PWM goes low the upper FET turns off and the
lower FET turns on. The HIP5011 has a PWM pin that inverts
the relationship from the input to PHASE. This architecture
allows the designer to utilize a low cost single-ended PWM
controller in either a current or voltage mode configuration. The
SynchroFEToperatesincontinuousconductionmodereducing
EMI constraints and enabling high bandwidth operation.
Severalfeaturesensureeasystart-up.First,thesupplycurrents
stay below specification as the supply voltages ramp up; no
unexpected surges occur that might perturb a soft-start or
deplete a charge-pump. Second, any power-up sequence of
the V
CC
, V
IN
, or PWM pins can be used without causing large
currents. Third, the chip operates when V
CC
is greater than 2V
so V
CC
can be created from a charge pump powered from V
IN
.
Features
Complementary Drive, Half-Bridge Power NMOS
Use With Low-Cost Single-Output PWM Controllers
Improve Efficiency Over Conventional Buck Converter with
Schottky Clamp
Minimum Deadtime Provided by Adaptive Shoot-Through
Protection Eliminates External Schottky
Grounded Case for Low EMI and Simple Heatsinking
Low Operating Current
Frequency Exceeding 1MHz
Dual Polarity Input Options
All Pins Surge Protected
Applications
5V to
≤
3.3V Synchronous Buck Converters
Pentium and P6 Power Supplies
PowerPC
Power Supplies
Bus Terminations (BTL and GTL)
Drive 5V Motors Directly from Microprocessor
Typical Application Block Diagram
Pentium is a registered trademark of Intel Corporation.
PowerPC is a trademark of International Business Machines.
SynchroFET is a trademark of Intersil Corporation.
Pinouts
HIP5010IS1, HIP5011IS1 (SIP - VERTICAL)
TOP VIEW
HIP5010IS, HIP5011IS (SIP - GULLWING)
TOP VIEW
1 PHASE
2 V
3 V
CC
4
5 PWM (HIP5010), PWM (HIP5011)
6 V
7 PHASE
GND (TAB)
FRONT ROWS = PINS 1, 3, 5, 7
BACK ROWS = PINS 2, 4, 6
1 PHASE
2 V
IN
3 V
CC
4
5 PWM (HIP5010), PWM (HIP5011)
6 V
7 PHASE
GND
(TAB)
Ordering Information
PART
NUMBER
TEMP.
RANGE (
o
C)
PACKAGE
PKG.
NO.
HIP5010IS
-40 to 85
7 Ld Gullwing SIP
Z7.05B
HIP5010IS1
-40 to 85
7 Ld Staggered Vertical SIP Z7.05C
HIP5011IS
-40 to 85
7 Ld Gullwing SIP
Z7.05B
HIP5011IS1
-40 to 85
7 Ld Staggered Vertical SIP Z7.05C
+12V
+3.3V
PHASE
PWM
V
IN
V
CC
CONTROL
+5V
HIP5010
PWM
CONTROLLER
SYNCHRONOUS RECTIFIED BUCK CONVERTER
GND
Data Sheet
March 1996
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
|
Copyright
Intersil Corporation 1999