- 您現在的位置：買賣IC網 > PDF目錄9758 > HI5766KCA (Intersil)IC ADC 10-BIT 60MSPS 28-SSOP PDF資料下載
參數資料
| 型號： | HI5766KCA |
| 廠商： | Intersil |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10-BIT 60MSPS 28-SSOP |
| 標準包裝： | 48 |
| 位數： | 10 |
| 采樣率（每秒）： | 60M |
| 數據接口： | 并聯 |
| 轉換器數目： | 8 |
| 功率耗散（最大）： | 260mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 28-SSOP/QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，雙極 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
12
two-bit multiplying digital-to-analog converter, follow the S/H
circuit with the ninth stage being a two bit flash converter.
Each converter stage in the pipeline will be sampling in one
phase and amplifying in the other clock phase. Each
individual subconverter clock signal is offset by 180 degrees
from the previous stage clock signal resulting in alternate
stages in the pipeline performing the same operation.
The output of each of the eight identical two-bit subconverter
stages is a two-bit digital word containing a supplementary bit
to be used by the digital error correction logic. The output of
each subconverter stage is input to a digital delay line which is
controlled by the internal sampling clock. The function of the
digital delay line is to time align the digital outputs of the eight
identical two-bit subconverter stages with the corresponding
output of the ninth stage flash converter before applying the
eighteen bit result to the digital error correction logic. The
digital error correction logic uses the supplementary bits to
correct any error that may exist before generating the final
10-bit digital data output of the converter.
Because of the pipeline nature of this converter, the digital
data representing an analog input sample is output to the
digital data bus on the 7th cycle of the clock after the analog
sample is taken. This time delay is specified as the data
latency. After the data latency time, the digital data
representing each succeeding analog sample is output during
the following clock cycle. The digital output data is
synchronized to the external sampling clock by a double
buffered latching technique. The output of the digital error
correction circuit is available in two’s complement or offset
binary format depending on the state of the Data Format
Select (DFS) control input (see Table 1, A/D Code Table).
Reference Voltage Inputs, VREF- and VREF+
The HI5766 is designed to accept two external reference
voltage sources at the VREF input pins. Typical operation of
the converter requires VREF+ to be set at +2.5V and VREF- to
be set at 2.0V. However, it should be noted that the input
structure of the VREF+ and VREF- input pins consists of a
resistive voltage divider with one resistor of the divider
(nominally 500
) connected between V
REF+ and VREF- and
the other resistor of the divider (nominally 2000
) connected
between VREF- and analog ground. This allows the user the
option of supplying only the +2.5V VREF+ voltage reference
with the +2.0V VREF- being generated internally by the
voltage division action of the input structure.
The HI5766 is tested with VREF- equal to +2.0V and VREF+
equal to +2.5V yielding a fully differential analog input voltage
range of
±0.5V. V
REF+ and VREF- can differ from the above
voltages.
In order to minimize overall converter noise it is
recommended that adequate high frequency decoupling be
provided at both of the reference voltage input pins, VREF+
and VREF-.
Analog Input, Differential Connection
The analog input to the HI5766 is a differential input that can
be configured in various ways depending on the signal
source and the required level of performance. A fully
differential connection (Figure 25 and Figure 26) will give the
best performance for the converter.
Since the HI5766 is powered by a single +5V analog supply,
the analog input is limited to be between ground and +5V.
For the differential input connection this implies the analog
input common mode voltage can range from 0.25V to 4.75V.
The performance of the ADC does not change significantly
with the value of the analog input common mode voltage.
A DC voltage source, VDC, equal to 3.2V (Typ), is made
available to the user to help simplify circuit design when using
an AC coupled differential input. This low output impedance
voltage source is not designed to be a reference but makes
an excellent DC bias source and stays well within the analog
input common mode voltage range over temperature.
For the AC coupled differential input (Figure 25) assume
the difference between VREF+, typically 2.5V, and VREF-,
typically 2V, is 0.5V. Full scale is achieved when the VIN
and -VIN input signals are 0.5VP-P, with -VIN being
180 degrees out of phase with VIN. The converter will be
at positive full scale when the VIN+ input is at
VDC + 0.25V and the VIN- input is at VDC - 0.25V (VIN+ -
VIN- = +0.5V). Conversely, the converter will be at
negative full scale when the VIN+ input is equal to VDC -
0.25V and VIN- is at VDC + 0.25V (VIN+ - VIN- = -0.5V).
The analog input can be DC coupled (Figure 26) as long as
the inputs are within the analog input common mode voltage
range (0.25V
≤ VDC ≤ 4.75V).
VIN+
VDC
VIN-
HI5766
VIN
-VIN
R
FIGURE 25. AC COUPLED DIFFERENTIAL INPUT
VIN+
VDC
VIN-
HI5766
VIN
-VIN
R
C
VDC
FIGURE 26. DC COUPLED DIFFERENTIAL INPUT
HI5766
相關PDF資料 |
PDF描述 |
|---|---|
| V375C15M150B | CONVERTER MOD DC/DC 15V 150W |
| MS27656E17B99PA | CONN RCPT 23POS WALL MNT W/PINS |
| MC10EP16VADG | IC RCVR/DRVR HV ECL DIFF 8SOIC |
| V375C12M150BG2 | CONVERTER MOD DC/DC 12V 150W |
| M83723/86A08037 | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5766KCAZ | 功能描述:模數轉換器 - ADC A/D 10-BIT 60MSPS 28 SSOP COM TEMP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| HI5766KCB | 功能描述:CONV A/D 10BIT 60MSPS 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| HI5766KCBS2503 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5766KCBZ | 功能描述:模數轉換器 - ADC 28 COMTEMP A/D 10BIT 60MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| HI5767 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:10-Bit, 20/40/60MSPS A/D Converter with Internal Voltage Reference |
發布緊急采購，3分鐘左右您將得到回復。