- 您現在的位置：買賣IC網 > PDF目錄370575 > HFCT-53D3 1 x 9 Fiber Optic Transceivers for Fibre Channel(光通道的1 x 9光纖收發器) PDF資料下載
參數資料
| 型號： | HFCT-53D3 |
| 英文描述： | 1 x 9 Fiber Optic Transceivers for Fibre Channel(光通道的1 x 9光纖收發器) |
| 中文描述： | 1 × 9光纖收發器適用于光纖通道（光通道的1 × 9光纖收發器） |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 314K |
| 代理商： | HFCT-53D3 |
10
Table 1. Pinout Table
Pin
Symbol
Mounting Pins The mounting pins are provided for transceiver mechanical attachment to the circuit board.
They are embedded in the nonconductive plastic housing and are not connected to the
transceiver internal circuit, nor is there a guaranteed connection to the metallized housing
in the EM and FM versions. They should be soldered into plated-through hole on the
printed circuit board.
1
V
EER
Receiver Signal Ground
Directly connect this pin to receiver signal ground plane. (For HFBR-53D3, V
EER
= V
EET
)
2
RD+
Receiver Data Out
RD+ is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
3
RD–
Receiver Data Out Bar
RD– is an open-emitter output circuit. Terminate this high-speed differential PECL output
with standard PECL techniques at the follow-on device input pin.
4
SD
Signal Detect
Normal optical input levels to the receiver result in a logic “1” output, V
OH
, asserted.
Low input optical levels to the receiver result in a fault condition indicated by a logic “0”
output V
OL
, deasserted.
Signal Detect is a single-ended PECL output. SD can be terminated with standard PECL
techniques via 50
to V
CCR
- 2 V. Alternatively, SD can be loaded with a 270
resistor to
V
EER
to conserve electrical power with small compromise to signal quality. If Signal Detect
output is not used, leave it open-circuited.
This Signal Detect output can be used to drive a PECL input on an upstream circuit, such
as, Signal Detect input or Loss of Signal-bar.
5
V
CCR
Receiver Power Supply
Provide +5 V dc via the recommended receiver power supply filter circuit.
Locate the power supply filter circuit as close as possible to the V
CCR
pin.
6
V
CCT
Transmitter Power Supply
Provide +5 Vdc via the recommended transmitter power supply filter circuit.
Locate the power supply filter circuit as close as possible to the V
CCT
pin.
7
TD–
Transmitter Data In-Bar
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
8
TD+
Transmitter Data In
Terminate this high-speed differential PECL input with standard PECL techniques at the
transmitter input pin.
9
V
EET
Transmitter Signal Ground
Directly connect this pin to the transmitter signal ground plane.
Functional Description
Figure 2. Pin-Out
1 = V
EER
2 = RD+
3 = RD–
4 = SD
5 = V
CCR
6 = V
CCT
7 = TD–
8 = TD+
9 = V
EET
TOP VIEW
NIC
NIC
RX
TX
NIC = NO INTERNAL CONNECTION (MOUNTING PINS)
相關PDF資料 |
PDF描述 |
|---|---|
| HFCT-53D5 | 1 x 9 Fiber Optic Transceivers for Gigabit Ethernet(千兆位以太網應用的1 x 9光纖收發器) |
| HFCT-5402D | 2488 Mb/s Single Mode Fiber Transceiver for SONET OC-48/SDH STM-16 and ATM(應用于SONET OC-48/SDH STM-16 和ATM的2488 Mb/s 單模式光收發器) |
| HFCT-5903E | MT-RJ Duplex Single Mode Transceiver(MT-RJ 雙工單模式收發器) |
| HFCT-5905E | MT-RJ Duplex Single Mode Transceiver(MT-RJ 雙工單模式收發器) |
| HFCT-6001D | 622 Mb/s Single Mode Fiber Transceiver for ATM, SONET OC-12/SDH STM-4(應用于ATM, SONET OC-12/SDH STM-4的622 Mb/s單模式光收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFCT53D3EM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HFCT-53D3EM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Extended Shield. Metalized Housing |
| HFCT53D3FM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HFCT-53D3FM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Flush Shield. Metalized Housing |
| HFCT53D5EM | 制造商:Agilent Technologies 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。