- 您現在的位置：買賣IC網 > PDF目錄370462 > HD404458 (Hitachi,Ltd.) 4-bit HMCS400-Series microcomputer(4位單片微計算機) PDF資料下載
參數資料
| 型號： | HD404458 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | 4-bit HMCS400-Series microcomputer(4位單片微計算機) |
| 中文描述： | 4位HMCS400系列微機（4位單片微計算機） |
| 文件頁數： | 102/120頁 |
| 文件大?。?/td> | 692K |
| 代理商： | HD404458 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁當前第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
HD404459 Series
102
Programming the Built-In PROM
The MCU’s built-in PROM is programmed in PROM mode. This PROM mode is set by pulling
TEST
,
M
0
,
and
M
1
low, and RESET high (figure 83). In PROM mode, the MCU does not operate, but it can be
programmed in the same way as any other commercial 27256-type EPROM using a standard PROM
programmer and a 64-to-28-pin socket adapter. Refer to table 31 for the Recommended PROM
programmers and socket adapters of the HD4074459.
Since an HMCS400-series instruction is ten bits long, the HMCS400-series MCU has a built-in conversion
circuit to enable the use of a general-purpose PROM programmer. This circuit splits each instruction into
five lower bits and five upper bits that are read from or written to consecutive addresses. This means that if,
for example, 16 kwords of built-in PROM are to be programmed by a general-purpose PROM programmer,
a 32-kbyte address space ($0000–$7FFF) must be specified.
Warnings
1. Always specify addresses $0000 to $7FFF when programming with a PROM programmer. If address
$8000 or higher is accessed, the PROM may not be programmed or verified correctly. Set all data in
unused addresses to $FF.
Note that the plastic-package versions cannot be erased or reprogrammed.
2. Make sure that the PROM programmer, socket adapter, and LSI are aligned correctly (their pin 1
positions match), otherwise overcurrents may damage the LSI. Before starting programming, make sure
that the LSI is firmly fixed in the socket adapter and the socket adapter is firmly fixed onto the
programmer.
3. PROM programmers have two voltages (V
PP
): 12.5 V and 21 V. Remember that ZTAT
TM
devices
require a V
PP
of 12.5 V—the 21-V setting will damage them. 12.5 V is the Intel 27256 setting.
Programming and Verification
The built-in PROM of the MCU can be program med at high speed without risk of voltage stress or damage
to data reliability.
Refer to table 30 for programming and verification modes.
For details of PROM programming, refer to the preface section, Notes on PROM Programming.
Table 30
PROM Mode Selection
Pin
CE
Mode
OE
V
PP
V
PP
V
PP
V
PP
O
0
–O
7
Data input
Programming
Low
High
Verification
High
Low
Data output
Programming inhibited
High
High
High impedance
相關PDF資料 |
PDF描述 |
|---|---|
| HD404459 | 4-bit HMCS400-Series microcomputer(4位單片微計算機) |
| HD40A4052 | 4-Bit Single-Chip Microcomputer(4位單片微計算機) |
| HD404092 | 4-Bit Single-Chip Microcomputer(4位單片微計算機) |
| HD404094 | 4-Bit Single-Chip Microcomputer(4位單片微計算機) |
| HD4074094 | 4-Bit Single-Chip Microcomputer(4位單片微計算機) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD404458H | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-bit HMCS400-series microcomputers |
| HD404459 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-bit HMCS400-series microcomputers |
| HD404459H | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-bit HMCS400-series microcomputers |
| HD404459SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| HD404508FS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。