• <var id="m9bhf"><label id="m9bhf"><noframes id="m9bhf"></noframes></label></var>
    <code id="m9bhf"><dl id="m9bhf"></dl></code>
    <i id="m9bhf"><label id="m9bhf"><th id="m9bhf"></th></label></i>
    <li id="m9bhf"><em id="m9bhf"></em></li>
    <dd id="m9bhf"><meter id="m9bhf"></meter></dd>
  • <dfn id="m9bhf"><thead id="m9bhf"></thead></dfn>
    <dd id="m9bhf"><tr id="m9bhf"><label id="m9bhf"></label></tr></dd>
  •         
    
    
    參數資料
    型號: HD404082
    廠商: Hitachi,Ltd.
    英文描述: Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    中文描述: 低電壓如同在微機芯片的A / D轉換器(帶片上的A / D轉換器的低壓微計算機)
    文件頁數: 85/162頁
    文件大?。?/td> 482K
    代理商: HD404082
    HD404374/HD404384/HD404389/HD404082/HD404084 Series
    85
    Timer C Operation
    Free-running/reload timer:
    Free-running/reload timer operation, the input clock source, and the prescaler division ratio are selected
    by means of timer mode register C1 (TMC1).
    Timer C is initialized to the value written to timer write register C (TWCL, TWCU) by software, and
    counts up by 1 each time the input clock is input. When the input clock is input after the timer C value
    reaches $FF, overflow output is generated. Timer C is then set to the value in timer write register C
    (TWCL, TWCU) if the reload timer function is selected, or to $00 if the free-running timer function is
    selected, and starts counting up again.
    Overflow output sets the timer C interrupt request flag (IFTC). This flag is reset by the program or by
    an MCU reset.
    For details, see figure 3, Interrupt Control Bit and Register Flag Area Configuration, and table 1, Initial
    Values after MCU Reset.
    16-bit timer operation:
    When timer B overflow flag is selected as the clock source, timer C can be used as a 16-bit timer that
    counts the timer B clock source pulses. In this case, since the timer B and timer C free-running/reload
    settings are independent, the settings should be made to suit the purpose.
    Watchdog timer operation:
    By using the timer C overflow output, timer C can be used as a watchdog timer for detecting program
    runaway. The watchdog timer is enabled when the watchdog on flag (WDON) is set to 1, and generates
    an MCU reset when timer C overflows. Usually, timer C initialization is performed by the program
    before the timer C value reaches $FF, so controlling program runaway.
    Timer output operation:
    With timer C, the R2
    0
    /TOC pin is designated as the TOC pin by setting bit 0 of port mode register 3
    (PMR3) to 1, and toggle waveform output or PWM waveform output can be selected by timer mode
    register C2 (TMC2).
    Toggle output
    The operation is similar to that for timer B toggle output.
    PWM output
    The operation is similar to that for timer B PWM output.
    Module standby:
    The operation is similar to that for timer B module standby.
    相關PDF資料
    PDF描述
    HD404084 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    HD40A4081 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    HD40C4081 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    HD40A4372 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    HD40A4374 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
    相關代理商/技術參數
    參數描述
    HD404082FT 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
    HD404082H 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
    HD404082S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
    HD404084 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip A/D Converter
    HD404092H 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:microcomputer designed to increase program productivity