2
HC5509A1R3060
Absolute Maximum Ratings
T
A
= 25
o
C
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +15V
Maximum Supply Voltages
(V
B+
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V
(V
B+
)-(V
B-
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +75V
Junction Temperature Plastic . . . . . . . . . . . . . . . . . . . . . . . . . 150
o
C
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . . 300
o
C
Thermal Information
Operating Conditions
Operating Temperature Range
HC4P5509A1R3060 . . . . . . . . . . . . . . . . . . . . . . . . . .0
o
C to 75
o
C
Storage Temperature Range . . . . . . . . . . . . . . . . . . -65
o
C to 150
o
C
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V to +12V
Positive Power Supply (V
B+
) . . . . . . . . . . . . . . . . . . . . . . . +5V
±
5%
Negative Power Supply (V
B-
) . . . . . . . . . . . . . . . . . . . . -42V to -58V
Loop Resistance (R
L
). . . . . . . . . . . . . . . . . 200
to 1750
(Note 2)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Thermal Resistance (Typical, Note 1)
PLCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .
θ
JA
(
o
C/W)
67
Die Characteristics
Transistor Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Diode Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Die Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 x 120
Substrate Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connected
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI
NOTES:
1.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
2. May be extended to 1900
with application circuit.
Electrical Specifications
Unless Otherwise Specified, Typical Parameters are at T
A
= 25
o
C, Min-Max Parameters are over Oper-
ating Temperature Range, V
B-
= -48V, V
B+
= +5V, AG = BG = 0V. All AC Parameters are specified at
600
2-Wire terminating impedance.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
AC TRANSMISSION PARAMETERS
RX Input Impedance
300Hz to 3.4kHz (Note 3)
-
100
-
k
TX Output Impedance
300Hz to 3.4kHz (Note 3)
-
-
20
4-Wire Input Overload Level
300Hz to 3.4kHz R
L
= 1200
,
600
Reference
+1.5
-
-
V
PEAK
2-Wire Return Loss
Matched for 600
(Note 3)
SRL LO
26
35
-
dB
ERL
30
40
-
dB
SRL HI
30
40
-
dB
2-Wire Longitudinal to Metallic Balance
Off Hook
Per ANSI/IEEE STD 455-1976 (Note 3) 300Hz
to 3400Hz
58
63
-
dB
4-Wire Longitudinal Balance
Off Hook
300Hz to 3400Hz (Note 3)
50
55
-
dB
Low Frequency Longitudinal Balance
R.E.A. Test Circuit
-
-
-67
dBmp
I
LINE
= 40mA T
A
= 25
o
C (Note 3)
-
-
23
dBrnC
Longitudinal Current Capability
I
LINE
= 40mA T
A
= 25
o
C (Note 3)
-
-
30
mA
RMS
Insertion Loss
0dBm at 1kHz, Referenced 600
2-Wire/4-Wire
-6.22
-6.02
-5.82
dB
4-Wire/2-Wire
-
±
0.05
±
0.2
dB
4-Wire/4-Wire
-6.22
-6.02
-5.82
dB