- 您現在的位置：買賣IC網 > PDF目錄370413 > HA11560T (Hitachi,Ltd.) Mini-Coax Crimp Tool Die; For Use With:Paladin Tools CrimpALL 8000 & 1300 Series Crimper; SMA, SMB BNC/TNC, Mini-UHF, Mini-59 , RG58, RG174, small coax & Belden 1855A RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | HA11560T |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | Mini-Coax Crimp Tool Die; For Use With:Paladin Tools CrimpALL 8000 & 1300 Series Crimper; SMA, SMB BNC/TNC, Mini-UHF, Mini-59 , RG58, RG174, small coax & Belden 1855A RoHS Compliant: Yes |
| 中文描述： | 錄像機/可變數據印刷射頻調制器 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 60K |
| 代理商： | HA11560T |
RF Oscillator/Channel Switch
A new type RF oscillator is employed to reduce RF
harmonics to a level that is dramatically lower than
previous available Hitachi products.
Note that using a capacitor lower than 0.22 μF at
pin 3 causes an increase in sync pulse sag.
The input resistance at pin 11, which is the
oscillator input pin, is 3 k
. Pins 9 and 10 are
oscillator output pins, and are NPN transistor
emitter-follower types.
The oscillator frequency is selectable by switching
the pin 7 channel switch between SAW resonator
low channel and high channel. When the channel
switch is open, oscillation output is performed
from pin 9, while grounding the switch causes
output from pin 10. The switching voltage of the
channel switch is approximately 2.1 V. When the
channel switch is grounded, a current of 30 μA
flows through pin 7, which is sufficient to drive an
electronic switch.
Antenna Switch
The antenna switch links the drive circuit that
switches the RF switch on and off with the chip’s
Figure 3 RF Oscillator Interface Circuit
RF oscillator on/off operation.
Opening the switch at pin 13 stops oscillation of
the RF oscillator and the antenna switch drive
output at pin 14 becomes 0 V. The audio system is
operating in this state, which acts to suppress
generation of popping noise in the audio as the
antenna switches between on and off.
When pin 13 is connected to V
CC
by a closed
switch, the RF oscillator is operational and the
antenna switch drive output DC level at pin 14 is
high.
Pin 13 should be connected to V
CC
when the
antenna switch is not used. A maximum current of
30 mA can be obtained from the antenna switch
driver.
Be sure to connect 10 k
for R3 at pin 13 when
the antenna switch is being used. R2 is used as
protective resistance when the antenna switch
power supply is switched on before the chip power
supply.
Figure 4 Antenna Switch Interface Circuit
11
10
9
7
3
SAW resonator
RF oscillator
Channel
switch
3 k
C2
0.22 μ
+
14
13
RF switch
RF oscillator
Antenna switch
driver
R2 10 k
V
CC
60 k
60 k
80 k
6
HA11560FP/T
相關PDF資料 |
PDF描述 |
|---|---|
| HA11560 | VCR/VDP RF Modulator |
| HA118104 | 3-circuit Video Switch |
| HA118104FP | 3-circuit Video Switch |
| HA118144AF | Video Camera CDS/AGC IC |
| HA12002 | PROTECTOR OF SPEAKERS AND POWER AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA11580 | 制造商:Panasonic Industrial Company 功能描述:I.C. |
| HA11585FPEL | 制造商:HITACHI 功能描述:* |
| HA11720 | 制造商:Panasonic Industrial Company 功能描述:I.C. |
| HA11732 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| HA11732MP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。