- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9064-CKDE3 (Gennum Corporation) GS9064 SD SDI Adaptive Cable Equalizer PDF資料下載
參數資料
| 型號： | GS9064-CKDE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS9064 SD SDI Adaptive Cable Equalizer |
| 中文描述： | GS9064標清SDI自適應電纜均衡器 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 162K |
| 代理商： | GS9064-CKDE3 |
GENNUM CORPORATION
22212 - 2
8 of 10
G
3. DETAILED DESCRIPTION
The GS9064 is a high speed bipolar IC designed to
equalize SD serial digital signals. The device can typically
equalize 350 meters of Belden
1694A cable
at 270Mb/s.
Powered from a single +3.3V or -3.3V power supply, the
device consumes approximately 240mW of power.
3.1 SERIAL DIGITAL INPUT
The SD serial digital input signal may be connected to the
input pins (SDI/SDI) in either a differential or single ended
configuration. AC coupling of the inputs is recommended,
as the SDI and SDI inputs are internally biased at
approximately +1.8 volts.
3.2 AUTOMATIC CABLE EQUALIZATION
The input signal passes through a variable gain equalizing
stage whose frequency response closely matches the
inverse of the cable loss characteristic. In addition, the vari-
ation of the frequency response with control voltage imitates
the variation of the inverse cable loss characteristic with
cable length.
The edge energy of the equalized signal is monitored by a
detector
circuit
which
produces
corresponding to the difference between the desired edge
energy and the actual edge energy. This error signal is
integrated by both an internal and an external AGC filter
capacitor providing a steady control voltage for the gain
stage. As the frequency response of the gain stage is
automatically varied by the application of negative
feedback, the edge energy of the equalized signal is kept
at a constant level which is representative of the original
edge energy at the transmitter.
an
error
signal
The equalized signal is also DC restored, effectively restor-
ing the logic threshold of the equalized signal to its correct
level independent of shifts due to AC coupling. The digital
output signals have a nominal voltage of 750mV
pp
differen-
tial, or 375mV
pp
single ended when terminated with 50
as
shown below in Figure 13.
Figure 13 Typical Output Voltage Levels
3.3 CABLE LENGTH INDICATION & CARRIER
DETECT/MUTE
The GS9064 incorporates an analog cable length indicator
(CLI) output and a programmable threshold output mute
(MCLADJ). In addition, a multi-function CD/MUTE pin allows
control of the GS9064 MUTE functionality for SD inputs.
3.3.1 Cable Length Indicator
The voltage output of the CLI pin is a representation of the
amount of cable present at the inputs of the device. Figure
8 shows the CLI voltage versus cable length (signal
strength). At 270Mb/s with no cable length and 800mV input
signal levels, the CLI output voltage is approximately 2.5V.
As the cable length is increased, the CLI voltage
decreases, thereby providing an approximate correlation
between the CLI voltage and cable length
3.3.2 Programmable Mute Threshold
A voltage programmable mute threshold (MCLADJ) is
included to allow muting of the GS9064 output when a
selected cable length is reached. This feature allows the
device to distinguish between low amplitude SDI signals
and noise at its input.
Figure 10 shows the relationship between the voltage
applied to the MCLADJ pin and the input cable length
accepted by the GS9064. For consistent accurate results
this may need to be calibrated for each device. The
MCLADJ pin may be left unconnected for applications
where output muting is not required.
This feature has been designed for use in applications such
as routers where signal crosstalk and circuit noise cause
the equalizer to output erroneous data when no input signal
is actually present. The use of a Carrier Detect function with
a fixed internal reference does not solve this problem since
the signal to noise ratio on the circuit board could be
significantly less than the default signal detection level set
by the on-chip reference.
NOTE: MCLADJ and CLI are only recommended for data
rates up to 360 Mb/s.
3.3.3 Carrier Detect/Mute
Applying a HIGH INPUT to the CD/Mute pin forces the
GS9064 outputs to a muted condition. See the DC Electrical
Characteristics table for voltage levels. In this condition the
outputs are latched to the last logic level present at the
output to avoid signal crosstalk.
Applying a LOW INPUT to the CD/Mute pin will force the
GS9064 outputs to remain active regardless of input cable
length or the voltage applied to the MCLADJ pin. See the DC
Electrical Characteristics table for voltage levels.
50
50
SDO
SDO
+187.5mV
-187.5mV
V
CM
= 2.925V
typical
+187.5mV
-187.5mV
V
CM
= 2.925V
typical
相關PDF資料 |
PDF描述 |
|---|---|
| GS9064A | GS9064A HD-LINX㈢ II Adaptive Cable Equalizer |
| GS9064ACKDE3 | GS9064A HD-LINX㈢ II Adaptive Cable Equalizer |
| GS9074A | GS9074A HD-LINX-R II Adaptive Cable Equalizer |
| GS9074ACNE3 | GS9074A HD-LINX-R II Adaptive Cable Equalizer |
| GS9078A | GS9078A HD-LINX-R II Multi-Rate Cable Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9064-CTD | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
| GS9064-CTDE3 | 制造商:Semtech Corporation 功能描述:SD/ASI Adaptive Equalizer |
| GS9065A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Multi-Rate SDI Automatic Reclocker |
| GS9065ACFUE3 | 制造商:Gennum Corporation 功能描述: |
| GS9065BCFUE3 | 功能描述:IC SDI RECLOCKER SMPTE 64LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
發布緊急采購，3分鐘左右您將得到回復。