- 您現在的位置：買賣IC網 > PDF目錄370377 > GS-D200 (意法半導體) 2/2.5A Bipolar Stepper Motor Driver Modules(2/2.5A雙極型步進電機驅動器模塊) PDF資料下載
參數資料
| 型號： | GS-D200 |
| 廠商： | 意法半導體 |
| 英文描述： | 2/2.5A Bipolar Stepper Motor Driver Modules(2/2.5A雙極型步進電機驅動器模塊) |
| 中文描述： | 2/2.5A雙極步進電機驅動器模塊（2/2.5A雙極型步進電機驅動器模塊） |
| 文件頁數： | 5/17頁 |
| 文件大小： | 183K |
| 代理商： | GS-D200 |
5/17
PIN DESCRIPTION
Pin
Function
Description
1
GND1
Return path for the logic signals and 5V supply.
2
Sync
Chopper oscillatoroutput.
Several modules can be synchronized by connectingtogether all Sync pins. This pin can
be used as the input for an external clock source.
3
Reset
Asynchronousreset input. An active low pulse on this input preset theinternal logic to the
initial state (ABCD=0101).
4
Half/Full
Half/Full stepselection input.
When high or unconnectedthe half stepoperation is selected.
5
Home
When high, this output indicatesthat the internal counteris in its initial state (ABCD=0101).
This signal may be usedin conjunctionwith a mechanical switch to groundor with open
collector output of an optical detector to be used as a systemhome detector.
6
Stepclk
The motor is movedone step on the risingedge of this signal.
7
CW/CCW
Direction control input. When high or unconnected clockwise rotation is selected.Physical
direction of motor rotationdepends also on windings connection.
8
Oscillator
The chopper oscillatortiming, internally fixed at 17kHz,can be modified byconnecting a
resistor between this pin and Vss or a capacitor between this pin and Gnd1.
The oscillatorinput mustbe grounded when the unit is externally synchronized.
9
Ioset
Phase current setting input. Aresistor connectedbetween this pin and Gnd1 or Vss,
allows the factory setted phase currentvalue (1Afor GS-D200and 2Afor GS-D200S) to
be changed.
10
Control
Logic input thatallows the phase current decay mode selection. When high or
unconnected the slow decay is selected.
11
Enable
Module enable input. When low this input floats the outputsenabling the manual
positioning of the motor. Must be LOW duringpower-up and down sequence, HIGH during
normal operation.
12
Vss
5V supplyinput. Maximum voltage must not exceed7V.
13
GND2
Return path for the power section.
14
D
D output.
15
C
C output.
16
B
B output.
17
A
A output.
18
Vs
Module and motor supply voltage.
Maximum voltage must not exceed the specified values.
GS-D200/GS-D200S
相關PDF資料 |
PDF描述 |
|---|---|
| GS-D200S | 2/2.5A Bipolar Stepper Motor Driver Modules(2/2.5A雙極型步進電機驅動器模塊) |
| GS-D500A | 100V/5A STEP AND MICROSTEP DRIVE BOARD FOR STEPPER MOTORS |
| GS-DC200 | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200S | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200SS | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GSD2004A | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Anode Small-Signal High-Voltage Switching Diode |
| GSD2004A-E3-08 | 制造商:Vishay Siliconix 功能描述:GSD2004A-E3-08 - Cut TR (SOS) 制造商:Vishay Intertechnologies 功能描述:SWITCHING DIODE GENPURP SOT23 |
| GSD2004A-E3-18 | 制造商:Vishay Siliconix 功能描述:GSD2004A-E3-18 - Bulk 制造商:Vishay Siliconix 功能描述:GSD2004A-E3-18 - Cut TR (SOS) 制造商:Vishay Intertechnologies 功能描述:SWITCHING DIODE GENPURP SOT23 |
| GSD2004A-G3-08 | 制造商:Vishay Siliconix 功能描述:GSD2004A-G3-08 - Bulk 制造商:Vishay Siliconix 功能描述:GSD2004A-G3-08 - Cut TR (SOS) 制造商:Vishay Intertechnologies 功能描述:SWITCHING DIODE GENPURP SOT23 |
| GSD2004A-G3-18 | 制造商:Vishay Siliconix 功能描述:GSD2004A-G3-18 - Bulk 制造商:Vishay Siliconix 功能描述:GSD2004A-G3-18 - Cut TR (SOS) 制造商:Vishay Intertechnologies 功能描述:SWITCHING DIODE GENPURP SOT23 |
發布緊急采購，3分鐘左右您將得到回復。