- 您現在的位置：買賣IC網 > PDF目錄94046 > FTL-8519-3D-2.5 FIBER OPTIC TRANSCEIVER, 820-860nm, 2125Mbps(Tx), 2125Mbps(Rx), PANEL MOUNT PDF資料下載
參數資料
| 型號： | FTL-8519-3D-2.5 |
| 元件分類： | 光收發 |
| 英文描述： | FIBER OPTIC TRANSCEIVER, 820-860nm, 2125Mbps(Tx), 2125Mbps(Rx), PANEL MOUNT |
| 封裝： | ROHS COMPLIANT PACKAGE-20 |
| 文件頁數： | 3/9頁 |
| 文件大?。?/td> | 169K |
| 代理商： | FTL-8519-3D-2.5 |
FTL-8519-3D-2.5 2.125Gb/s GBIC Product Specification – November 2007
Finisar
Finisar Corporation November 16, 2007 Rev. D3
Page 3
II.
Electrical Power Interface
Finisar FTL-8519-3D-2.5 GBICs have an extended power supply voltage range of 3.15 V
to 5.5 V as described in Table 2. They are compatible with both 3.3V and 5 V systems.
+5/3.3 Volt Electrical Power
Interface
Parameter
Symbol
Min
Typ
Max
Units
Notes/Conditions
Supply Current
Is
190
300
mA
Surge Current
Isurge
330
mA
Hot plug
Absolute Supply Voltage
Vmax
-0.3
6
V
Not to be applied
continuously
Operating Supply Voltage
Vcc
3.15
3.3, 5
5.5
V
Referenced to GND.
Table 2. Electrical power interface
III. Low Speed Signals
RX_LOS, and TX_DISABLE are TTL signals as described in Table 3. MOD_DEF(1)
(SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VI, “Serial
Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to
host_Vcc. If host_Vcc is 3.3V, then they must be pulled to 3.3V. If host_Vcc is 3.3V,
do not pull the MOD_DEF pins to 5V. For more detailed information, see sections 5.3.1
– 5.3.8 in the GBIC Specification Rev. 5.5
1.
Low Speed Signals, Electronic
Characteristics
Parameter
Symbol
Min
Max
Units Notes/Conditions
GBIC Output LOW
VOL
0
0.5
V
4.7k to 10k pull-up to host_Vcc,
measured at host side of connector
GBIC Output HIGH
VOH
host_Vcc - 0.5 host_Vcc + 0.3
V
4.7k to 10k pull-up to host_Vcc,
measured at host side of connector
GBIC Input LOW
VIL
0
0.8
V
4.7k to 10k pull-up to Vcc,
measured at GBIC side of
connector*
GBIC Input HIGH
VIH
2
Vcc + 0.3
V
4.7k to 10k pull-up to Vcc,
measured at GBIC side of
connector*
*Note VIH and VIL are the same for both 5V and 3.3V operation
Table 3. Low speed signals – electronic characteristics
相關PDF資料 |
PDF描述 |
|---|---|
| FTL-8519-3D-DD | FIBER OPTIC TRANSCEIVER, 820-860nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT |
| FTLF1318P2BCL | FIBER OPTIC TRANSCEIVER, 1270-1360nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| FTLF1318P2WCL | FIBER OPTIC TRANSCEIVER, 1270-1360nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT, LC CONNECTOR |
| FTLF1319F1GTL | FIBER OPTIC TRANSCEIVER, 1270-1355nm, 2125Mbps(Tx), 2125Mbps(Rx), THROUGH HOLE MOUNT, LC CONNECTOR |
| FTLF1319F1HTL | FIBER OPTIC TRANSCEIVER, 1270-1355nm, 2125Mbps(Tx), 2125Mbps(Rx), THROUGH HOLE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FTL-8519-3D-DD | 制造商:Finisar Corporation 功能描述:TX/RX OPTICAL FIBER 1250MBPS - Trays |
| FT-L8Y | 制造商:Panasonic Electric Works 功能描述:FIBER SENSOR5.5MM DIA. THRU. CHEMICAL-R |
| FTLC1151RDPL | 功能描述:Fiber Optic Transceiver Module Ethernet 103.1Gbps 1300nm 3.3V LC Duplex Pluggable, QSFP 制造商:finisar corporation 系列:- 零件狀態:有效 數據速率:103.1Gbps 波長:1300nm 應用:以太網 電壓 - 電源:3.3V 連接器類型:LC 雙工 安裝類型:可插入式，QSFP 標準包裝:1 |
| FTLC1152RGPL | 功能描述:Fiber Optic Transceiver Module General Purpose 103.1Gbps 1300nm 3.3V LC Duplex Pluggable, QSFP 制造商:finisar corporation 系列:- 零件狀態:有效 數據速率:103.1Gbps 波長:1300nm 應用:通用 電壓 - 電源:3.3V 連接器類型:LC 雙工 安裝類型:可插入式，QSFP 標準包裝:1 |
| FTLC1181RDNA | 制造商:Finisar Corporation 功能描述:4X25G LAN WDM EML, 4X25G PIN, 100GBASE-LR4 10KM 100GBE, 103G - Bulk |
發布緊急采購，3分鐘左右您將得到回復。