參數資料
型號: FSA3200UMX
廠商: Fairchild Semiconductor
文件頁數: 6/13頁
文件大?。?/td> 0K
描述: IC ANALOG USB VID SWITCH 16UMLP
標準包裝: 5,000
功能: USB 開關
電路: 2 x DPST,2 x SPDT
導通狀態電阻: 6.5 歐姆
電壓電源: 單電源
電壓 - 電源,單路/雙路(±): 2.7 V ~ 4.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-UFQFN
供應商設備封裝: 16-UMLP(1.8x2.6)
包裝: 帶卷 (TR)
2010 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FSA3200 Rev. 1.0.8
2
FSA3200
Two-Port,
High-Speed
USB2.0
Switch
with
Mobile
High-De
finition
Link
(MHL)
Switch Power Operation
In normal operation, the FSA3200 is powered from the
VCC pin, which typically is derived from a regulated
power management device. In special circumstances,
such as production test or system firmware upgrade, the
device can be powered from the VBUS pin. In this mode
of operation, a valid VBUS voltage is present (per USB2.0
specification) and VCC=0 V, typically due to a no-battery
condition. With the SELn pins strapped LOW (via
external resistor), the FSA3200 closes the USB path,
enabling the initial programming of the system directly
from the USB connector. Once the system has normal
operating supply power with VCC present, the VBUS
supply is not utilized and normal switch operation
commences. Optionally, the Power Select Override
(PSO) pin can be set HIGH to force the device to be
powered from VBUS.
The VBUS / VCC detection capability is not intended to be
an accurate determination of the voltages present,
rather a state condition detection to determine which
supply should be used. These state determinations rely
on the voltage conditions as described in the Electrical
Characterization tables below.
Figure 2. Simplified Logic of Switch Power Selection Circuit
Table 1. Switch Power Selection Truth Table
VCC
VBUS
PSO
(1)
Switch Power Source
0
No switch power, switch paths high-Z
0
1
0
VBUS
1
0
VCC
1
0
VCC
0
1
No switch power, switch paths high-Z
0
1
VBUS
1
0
1
VCC
(2)
1
VBUS
Notes:
1.
Control inputs should never be left floating or unconnected. If the PSO function is used, a weak pull-up resistor
(3 M) should be used to minimize static current draw. If the PSO function is not used, tie directly to GND.
2.
PSO control is overridden with no VBUS and the power selection is switched to VCC.
Table 2. Data Switch Select Truth Table
SEL1
(3)
SEL2
(3)
Function
0
D+/D- connected to USB+/USB-, IDCO connected to IDUSB
0
1
D+/D- connected to USB+/USB-, IDCOM connected to IDMDV
1
0
D+/D- connected to MDV+/MDV-, IDCOM connected to IDUSB
1
D+/D- connected to MDV+/MDV-, IDCOM connected to IDMDV
Note:
3.
Control inputs should never be left floating or unconnected. To guarantee default switch closure to the USB
position, the SEL pins should be tied to GND with a weak pull- down resistor (3 M) to minimize static current draw.
PSO
VCC
VBUS
Switch
Power
Charge Pump
& Regulator
Switch
Power
Selection
Switch
Power
Source
相關PDF資料
PDF描述
FSA321UMX IC SWITCH MULTIMEDIA 10-UMLP
FSA3259BQX IC SWITCH DUAL SP3T 16DQFN
FSA3357K8X IC SWITCH SP3T US8
FSA4157AL6X_F087 IC SWITCH SPDT 6MICROPAK
FSA4159L6X_F113 IC SWITCH SPDT 6MICROPAK
相關代理商/技術參數
參數描述
FSA3200UMX_F106 功能描述:電源開關 IC - USB USB SW DPDT 5V RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube
FSA321 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths
FSA321_12 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths
FSA321UMX 功能描述:多路器開關 IC USB 2.0 Hi-Speed and Audio Switch RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16
FSA321UMX_F113 功能描述:多路器開關 IC Multimedia & USB2 Hi-Speed & Aud Swtch RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻(最大值):7 Ohms 開啟時間(最大值): 關閉時間(最大值): 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16