- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5019BMTCX (FAIRCHILD SEMICONDUCTOR CORP) 6-Bit VID Controller 2-4 Phase VR10.X Controller PDF資料下載
參數資料
| 型號： | FAN5019BMTCX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| 中文描述： | SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | LEAD FREE, MO-153AB, TSSOP-28 |
| 文件頁數： | 28/30頁 |
| 文件大?。?/td> | 508K |
| 代理商： | FAN5019BMTCX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁
FAN5019B
PRODUCT SPECIFICATION
28
REV. 1.0.0 Jul/15/05
Whenever a power dissipating component (e.g., a power
MOSFET) is soldered to a PCB, the liberal use of vias,
both directly on the mounting pad and immediately
surrounding it, is recommended. Two important reasons
for this are: improved current rating through the vias, and
improved thermal performance from vias extended to the
opposite side of the PCB where a plane can more readily
transfer the heat to the air. To achieve the best thermal
dissipation to the air around the board, make a mirror
image of any pad being used to heatsink the MOSFETs on
the opposite side of the PCB . To further improve thermal
performance, use the largest possible pad area.
Route the output power path to encompass a short
distance. The output power path is formed by the current
path through the inductor, the output capacitors, and the
load.
For best EMI containment, use a solid power ground
plane as one of the inner layers extending fully under all
the power components.
Signal Circuitry
The output voltage is sensed and regulated between the
FB pin and the FBRTN pin (which connects to the signal
ground at the load). To avoid differential mode noise
pickup in the sensed signal, the loop area should be small.
Thus the FB and FBRTN traces should be routed adjacent
to each other atop the power ground plane back to the
controller.
Connect the feedback traces from the switch nodes as
close as possible to the inductor. Connect the CSREF
signal to the output voltage at the nearest inductor to the
controller.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5019MTC | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019MTCX | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019 | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5026 | Dual DDR/Dual-output PWM Controller |
| FAN5026MTC | Dual DDR/Dual-output PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5019MTC | 功能描述:DC/DC 開關控制器 PWM 4 phases contrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5019MTCX | 功能描述:DC/DC 開關控制器 Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN501MPX | 制造商:Fairchild Semiconductor Corporation 功能描述:PWM CONTROLLER - Tape and Reel |
| FAN5020_AAC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5021_AAC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。