- 您現在的位置：買賣IC網 > PDF目錄375717 > FAN1581 (Fairchild Semiconductor Corporation) 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator PDF資料下載
參數資料
| 型號： | FAN1581 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
| 中文描述： | 第5A可調/固定超低壓差線性穩壓器 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 85K |
| 代理商： | FAN1581 |
FAN1581
PRODUCT SPECIFICATION
6
REV. 1.2.0 11/6/03
General
The FAN1581, FAN1581-1.2, FAN1581-1.5, and
FAN1581-2.5 are three-terminal regulators optimized for
DDR and GTL+ V
TT
termination and logic applications.
These devices are short-circuit protected, and offer thermal
shutdown to turn off the regulator when the junction temper-
ature exceeds about 150°C. The FAN1581 series provides
low dropout voltage and fast transient response. Frequency
compensation uses capacitors with low ESR while still main-
taining stability. This is critical in addressing the needs of
low voltage high speed microprocessor buses like GTL+.
V
IN
and V
CNTL
Functions
The FAN1581 utilizes a dual supply approach to maximize
efficiency. The collector of the power device is brought out
to the V
IN
pin to minimize internal power dissipation under
high current loads. V
CNTL
provides power for the control
circuitry and the drive for the output NPN transistor.
V
CNTL
should be at least 1.2 V higher than the output volt-
age. Special care was taken to ensure there are no supply-
sequencing problems. The output voltage will not turn on
until both supplies are operating. If the control voltage
comes up first, the output current will be typically limited to
about 3.0 mA until the power input voltage comes up. If the
power input voltage comes up first the output will not turn on
at all until the control voltage comes up. The output can
never come up unregulated.
The FAN1581 can also be used as a single supply device
with the control and power inputs tied together. In this mode,
the dropout is determined by the minimum control voltage.
Stability
The FAN1581 series requires an output capacitor as a part of
the frequency compensation. It is recommended to use a 22μF
solid tantalum or a 100μF aluminum electrolytic on the output
to ensure stability. The frequency compensation of these
devices optimizes the frequency response with low ESR capaci-
tors. In general, it is suggested to use capacitors with an ESR
of < 0.3
. It is also recommended to use bypass capacitors
such as a 22μF tantalum or a 100μF aluminum on the
adjust pin of the FAN1581 for low ripple and fast transient
response. When these bypassing capacitors are not used at the
adjust pin, smaller values of output capacitors provide equally
good results. A graph showing stability of output capacitance
ESR vs load current can be found under Typical Performance
Characteristics.
Protection Diodes
In normal operation, the FAN1581 series does not require any
protection diodes. For the FAN1581, internal resistors limit
internal current paths on the adjust pin. Therefore, even with
bypass capacitors on the adjust pin, no protection diode is
needed to ensure device safety under short-circuit conditions.
A protection diode between the input and output pins is
usually not needed. An internal diode between the input and
the output pins on the FAN1581 series can handle microsec-
ond surge currents of 50A to 100A. Even with large value
output capacitors it is difficult to obtain those values of surge
currents in normal operation. Only with large values of out-
put capacitance, such as 1000μF to 5000μF, and with the
input pin instantaneously shorted to ground can damage
occur. A crowbar circuit at the input can generate those levels of
current; a diode from output to input is then recommended,
as shown in Figure 1. Usually, normal power supply cycling
or system “hot plugging and unplugging” will not generate
current large enough to do any damage.
Figure 1. Optional Protection Diode
Ripple Rejection
In applications that require improved ripple rejection, a bypass
capacitor from the adjust pin of the FAN1581 to ground
reduces the output ripple by the ratio of V
OUT
/1.25V. The
impedance of the adjust pin capacitor at the ripple frequency
should be less than the value of R1 (typically in the range of
100
to 120
) in the feedback divider network in Figure 1.
Therefore, the value of the required adjust pin capacitor is a
function of the input ripple frequency. For example, if R1 equals
100
and the ripple frequency equals 120Hz, the adjust pin
capacitor should be 22μF. At 10kHz, only 0.22μF is needed.
Output Voltage
The FAN1581 regulator develops a 1.25V reference voltage
between the output pin and the adjust pin (see Figure 2).
Placing a resistor R1 between these two terminals causes a
constant current to flow through R1 and down through R2 to
set the overall output voltage. Normally, this current is the
specified minimum load current of 10mA.
FAN1581
Adj
Vin
C2
22
μ
F
V
OUT
+
C1
10
μ
F
+
C
ADJ
+
Vcntl
Vsense
Vout
R1
R2
D1
1N4002
(OPTIONAL)
V
IN
V
OUT
FAN1581
Gnd
Vin
C2
22
μ
F
V
OUT
+
C1
10
μ
F
+
Vcntl
Vsense
Vout
D1
1N4002
(OPTIONAL)
V
IN
V
CNTL
相關PDF資料 |
PDF描述 |
|---|---|
| FAN1581D15X | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
| FAN1581D25X | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
| FAN1581DX | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
| FAN1581M12X | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
| FAN1581M25X | 5A Adjustable/Fixed Ultra Low Dropout Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN1581D15X | 功能描述:低壓差穩壓器 - LDO 5A Adjustable Low Dropout Voltage Regulator (LDO) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| FAN1581D25X | 功能描述:低壓差穩壓器 - LDO 5A Adjustable Low Dropout Voltage Regulator (LDO) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| FAN1581DX | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| FAN1581M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Adjustable Voltage Regulator |
| FAN1581M-1.5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Fixed Voltage Regulator |
發布緊急采購，3分鐘左右您將得到回復。