- 您現在的位置：買賣IC網 > PDF目錄17052 > EVAL-AD7725CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7725 PDF資料下載
參數資料
| 型號： | EVAL-AD7725CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7725 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 900k |
| 數據接口： | 串行，并聯 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 615mW @ 900kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7725 |
| 已供物品： | 板，CD |
| 相關產品： | AD7725BSZ-ND - IC ADC 16BIT PROG 44MQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
REV. A
–16–
AD7725
A
B
A
B
500
AC GROUND
CLKIN
A
B
2pF
VIN(+)
VIN(–)
AD7725
Figure 11. Analog Input Equivalent Circuit
Driving the Analog Inputs
To interface the signal source to the AD7725, at least one op
amp will generally be required. The choice of op amp will be
critical to achieving the full performance of the AD7725. The
op amp not only has to recover from the transient loads that the
ADC imposes on it, but it must also have good distortion char-
acteristics and very low input noise. Resistors in the signal path
will also add to the overall thermal noise floor, necessitating the
choice of low value resistors.
Placing an RC filter between the drive source and the ADC
inputs, as shown in Figure 12, has a number of beneficial
effects: transients on the op amp outputs are significantly
reduced since the external capacitor now supplies the instanta-
neous charge required when the sampling capacitors are switched
to the ADC input pins, and input circuit noise at the sample
images is now significantly attenuated, resulting in improved
overall SNR. The external resistor serves to isolate the external
capacitor from the ADC output, thus improving op amp stabil-
ity while also isolating the op amp output from any remaining
transients on the capacitor. By experimenting with different
filter values, the optimum performance can be achieved for each
application. As a guideline, the RC time constant (R
C) should
be less than a quarter of the clock period to avoid nonlinear
currents from the ADC inputs being stored on the external
capacitor and degrading distortion. This restriction means that
this filter cannot form the main antialias filter for the ADC.
R
C
AD7725
VIN(+)
VIN(–)
Figure 12. Input RC Network
With the unipolar input mode selected, just one op amp is
required to buffer the single-ended input signal to the VIN(+)
input, and a dc input is applied to the VIN(–) pin to provide an
offset. However, driving the AD7725 with differential signals
(i.e., the bipolar input range is selected) has some distinct
advantages: even-order harmonics in both the drive circuits and
the AD7725 front end are attenuated, and the peak-to-peak
input signal range on both inputs is halved. Halving the input
signal range allows some op amps to be powered from the same
supplies as the AD7725. An example of providing differential
drive to the AD7725 is to use a dual op amp.
Dual Op Amp
Although this differential drive circuit will require two op amps
per ADC, it may avoid the need to generate additional supplies
just for these op amps.
Figures 13 and 14 show two circuits for driving the AD7725.
Figure 13 is intended for use when the input signal is biased
about 2.5 V, while Figure 14 is used when the input signal is
biased about ground. While both circuits convert the input
signal into a differential signal, the circuit in Figure 14 also level
shifts the signal so that both outputs are biased about 2.5 V.
Suitable op amps include the AD8047, the AD8041 and its dual
equivalent the AD8042, or the AD8022. The AD8047 has
lower input noise than the AD8041/AD8042 but has to be
supplied from a +7.5 V/–2.5 V supply. The AD8041/AD8042
will typically degrade the SNR from 83 dB to 81 dB but can be
powered from the same single 5 V supply as the AD7725.
220pF
AD7725
VIN(+)
VIN(–)
27
RIN
390
220
10k
10nF
220nF
1 F
27
RSOURCE
AIN =
2V
BIASED
ABOUT +2.5V
REF2
REF1
RFB
220
50
V+
V–
V+
V–
Figure 13. Single-Ended-to-Differential Input Circuit
for Bipolar Mode Operation (Analog Input Biased
about 2.5 V)
相關PDF資料 |
PDF描述 |
|---|---|
| REC5-4805SRW/H6/C | CONV DC/DC 5W 36-72VIN 05VOUT |
| REC5-4805SRW/H6/A | CONV DC/DC 5W 36-72VIN 05VOUT |
| EVAL-AD7796EBZ | BOARD EVALUATION FOR AD7796 |
| GSM10DRSI-S288 | CONN EDGECARD 20POS .156 EXTEND |
| ECC50DJBN | CONN EDGECARD 100POS .100X.200 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7730EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7730EBZ | 功能描述:BOARD EVAL FOR AD7730 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7730LEB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7730LEBZ | 功能描述:BOARD EVALUATION FOR AD7730 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7731EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。