參數資料
型號: EVAL-AD7689EDZ
廠商: Analog Devices Inc
文件頁數: 20/32頁
文件大小: 0K
描述: BOARD EVAL AD7689
產品培訓模塊: Motor Control
標準包裝: 1
系列: PulSAR®
ADC 的數量: 1
位數: 16
采樣率(每秒): 250k
數據接口: 串行
輸入范圍: ±VREF
在以下條件下的電源(標準): 12.5mW @ 250kSPS,5V
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD7689
已供物品:
Data Sheet
AD7682/AD7689
Rev. D | Page 27 of 32
GENERAL TIMING WITH A BUSY INDICATOR
Figure 38 details the timing for all three modes: read/write
during conversion (RDC), read/write after conversion (RAC),
and read/write spanning conversion (RSC). Note that the gating
item for both CFG and data readback is at the end of conversion
(EOC). As detailed previously, the data access should occur up
to safe data reading/writing time, tDATA. If the full CFG word is
not written to prior to EOC, it is discarded and the current
configuration remains.
At the EOC, if CNV is low, the busy indicator is enabled. In
addition, to generate the busy indicator properly, the host must
assert a minimum of 17 SCK falling edges to return SDO to high
impedance because the last bit on SDO remains active. Unlike the
Busy Indicator section, if the conversion result is not read out
fully prior to EOC, the last bit clocked out remains. If this bit is
low, the busy signal indicator cannot be generated because the
busy generation requires either a high impedance or a remaining
bit high-to-low transition. A good example of this occurs when
an SPI host sends 16 SCKs because these are usually limited to
8-bit or 16-bit bursts; thus the LSB remains. Because the transi-
tion noise of the AD7682/AD7689 is 4 LSBs peak to peak (or
greater), the LSB is low 50% of the time. For this interface, the SPI
host needs to burst 24 SCKs, or a QSPI interface can be used and
programmed for 17 SCKs.
The SCK can idle high or low depending on the CPOL and
CPHA settings if SPI is used. A simple solution is to use CPOL =
CPHA = 1 (not shown) with SCK idling high.
From power-up, in any read/write mode, the first three conver-
sion results are undefined because a valid CFG does not take
place until the 2nd EOC; thus, two dummy conversions are
required. Also, if the state machine writes the CFG during the
power-up state (RDC shown), the CFG register needs to be
rewritten again at the next phase. Note that the first valid data
occurs in Phase (n + 1) when the CFG register is written during
Phase (n 1).
ACQUISITION
(n – 1) UNDEFINED
ACQUISITION
(n)
ACQUISITION
(n + 1)
ACQUISITION
(n + 2)
PHASE
POWER
UP
EOC
START OF CONVERSION
(SOC)
EOC
CONVERSION
(n)
CONVERSION
(n + 1)
CONVERSION
(n – 2) UNDEFINED
07
35
3-
04
4
tCONV
tCYC
tDATA
CNV
DIN
RDC
RAC
RSC
SDO
NOTES
1. CNV MUST BE LOW PRIOR TO THE END OF CONVERSION (EOC) TO GENERATE THE BUSY INDICATOR.
2. A TOTAL OF 17 SCK FALLING EDGES ARE REQUIRED TO RETURN SDO TO HIGH-Z. IF CFG READBACK IS ENABLED,
A TOTAL OF 31 SCK FALLING EDGES IS REQUIRED TO RETURN SDO TO HIGH-Z.
DATA (n)
DATA (n – 1)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 2)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 1)
XXX
DATA (n – 3)
XXX
DIN
SDO
DATA (n + 1)
DATA (n)
DATA (n + 1)
DIN
CFG (n)
CFG (n + 2)
CFG (n + 1)
CFG (n + 3)
SDO
SCK
1
SCK
1n
n + 1
17
1
n
n + 1
17
1
n
n + 1
17
SCK
1
XXX
NOTE 1
NOTE 2
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n)
CFG (n + 1)
CFG (n + 2)
CFG (n + 3)
CONVERSION
(n – 1) UNDEFINED
Figure 38. General Interface Timing for the AD7682/AD7689 With a Busy Indicator
相關PDF資料
PDF描述
VE-J1J-EY CONVERTER MOD DC/DC 36V 50W
EVAL-AD7682EDZ BOARD EVAL AD7682
LGU2E331MELZ CAP ALUM 330UF 250V 20% SNAP
EVAL-AD7982SDZ BOARD EVAL FOR AD7982
VI-J1L-EY CONVERTER MOD DC/DC 28V 50W
相關代理商/技術參數
參數描述
EVAL-AD7689EDZ 制造商:Analog Devices 功能描述:16 Bit A/D Converter Eval. Board
EVAL-AD7690CB 制造商:Analog Devices 功能描述:AD7690 EVAL - Bulk
EVAL-AD7690SDZ 功能描述:BOARD EVAL FOR AD7690 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7691CBZ 功能描述:BOARD EVALUATION FOR AD7691CBZ RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7691SDZ 功能描述:BOARD EVAL FOR AD7691 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件