參數資料
型號： EVAL-AD7623CBZ
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大小： 0K
描述： BOARD EVALUATION FOR AD7623
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 16
采樣率（每秒）： 1.33M
數據接口： 串行，并聯
輸入范圍： ±VREF
在以下條件下的電源（標準）： 50mW @ 1.33MSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7623
已供物品： 板
相關產品： AD7623ASTZ-ND - IC ADC 16BIT 1.33MSPS DFF 48LQFP
AD7623ACPZ-ND - IC ADC 16BIT 1.33MSPS 48LFCSP
AD7623ACPZRL-ND - IC ADC 16BIT 1.33MSPS 48LFCSP
AD7623ASTZRL-ND - IC ADC 16BIT 1.33MSPS DFF 48LQFP
AD7623
Rev. 0 | Page 19 of 28
External Reference (PDBUF = High, PRBUF = High)
To use an external reference directly on the REF pin, PDREF
and PDBUF should both be high. PDREF and PDBUF power
down the internal reference and the internal reference buffer,
respectively.
For improved drift performance, an external reference, such as
the AD780 or ADR431, can be used. The advantages of directly
using the external voltage reference are:
SNR and dynamic range improvement (about 1.7 dB)
resulting from the use of a reference voltage very close to
the supply (2.5 V) instead of a typical 2.048 V reference
when the internal reference is used. This is calculated by
=
048
.
2
50
.
2
log
20
SNR
Power savings when the internal reference is powered
down (PBREF = PDBUF = high).
Reference Decoupling
Whether using an internal or external reference, the AD7623
voltage reference input (REF) has a dynamic input impedance;
therefore, it should be driven by a low impedance source with
efficient decoupling between the REF and REFGND inputs.
This decoupling depends on the choice of the voltage reference,
but usually consists of a low ESR capacitor connected to REF
and REFGND with minimum parasitic inductance. A 10 μF
(X5R, 1206 size) ceramic chip capacitor (or 47 μF tantalum
capacitor) is appropriate when using either the internal
reference or one of these recommended reference voltages:
The low noise, low temperature drift ADR431 and AD780
The low power ADR291
The low cost AD1582
The placement of the reference decoupling is also important to
the performance of the AD7623. The decoupling capacitor
should be mounted on the same side as the ADC right at the
REF pin with a thick PCB trace. The REFGND should also
connect to the reference decoupling capacitor with the shortest
distance.
For applications that use multiple AD7623 devices, it is more
effective to use the internal reference buffer to buffer the
reference voltage.
The voltage reference temperature coefficient (TC) directly
impacts full scale; therefore, in applications where full-scale
accuracy matters, care must be taken with the TC. For instance,
a ±15 ppm/°C TC of the reference changes full-scale by ±1 LSB/°C.
Temperature Sensor
The TEMP pin measures the temperature of the AD7623. To
improve the calibration accuracy over the temperature range,
the output of the TEMP pin is applied to one of the inputs of
the analog switch (such as ADG779), and the ADC itself is used
to measure its own temperature. This configuration is shown
05574-028
ADG779
AD8021
CC
ANALOG INPUT
(UNIPOLAR)
AD7623
IN+
TEMPERATURE
SENSOR
TEMP
Figure 28. Use of the Temperature Sensor
POWER SUPPLY
The AD7623 uses three sets of power supply pins: an analog
2.5 V supply AVDD, a digital 2.5 V core supply DVDD, and a
digital input/output interface supply OVDD. The OVDD supply
allows direct interface with any logic working between 2.3 V
and 5.25 V. To reduce the number of supplies needed, the digital
core (DVDD) can be supplied through a simple RC filter from
the analog supply, as shown in Figure 23.
Power Sequencing
The AD7623 is independent of power supply sequencing once
OVDD does not exceed DVDD by more than 0.3 V until
DVDD = 2.3 V during any time; for instance, at power-up or
power-down (see the Absolute Maximum Ratings section).
Additionally, it is very insensitive to power supply variations
over a wide frequency range as shown in Figure 29.
05574-029
FREQUENCY (kHz)
P
S
RR
(dB)
45
75
70
65
60
55
50
1
10
100
1k
10k
EXT REF
INT REF
Figure 29. PSRR vs. Frequency
相關PDF資料
PDF描述
RMC05DREN-S93 CONN EDGECARD 10POS .100 EYELET
0210491052 CABLE JUMPER 1.25MM .030M 35POS
N001-025-BL-R CABLE PATCH CAT5E BLUE 25'
EVAL-AD7622CBZ BOARD EVALUATION FOR AD7622
RBC08DREN-S93 CONN EDGECARD 16POS .100 EYELET
相關代理商/技術參數
參數描述
EVAL-AD7623EDZ 功能描述:BOARD EVAL FOR AD7623 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7625EDZ 功能描述:數據轉換 IC 開發工具 Eval Board 16-BIT 5MSPS ADC I.C RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7626EDZ 功能描述:數據轉換 IC 開發工具 Eval Board 16 Bit 10MSPS DIFF ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7631CBZ 制造商:Analog Devices 功能描述:EVALUATION BOARD - Boxed Product (Development Kits)
EVAL-AD7631EDZ 功能描述:BOARD EVAL FOR AD7631 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*