參數資料
型號： EVAL-AD5781SDZ
廠商： Analog Devices Inc
文件頁數： 17/28頁
文件大小： 0K
描述： BOARD EVAL FOR AD5781
標準包裝： 1
DAC 的數量： 1
位數： 18
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
設置時間： 1µs
DAC 型： 電壓
工作溫度： -40°C ~ 125°C
已供物品： 板，CD
已用 IC / 零件： AD5781
AD5781
Data Sheet
Rev. D | Page 24 of 28
AD5781 FEATURES
POWER-ON TO 0 V
The AD5781 contains a power-on reset circuit that, as well as
resetting all registers to their default values, controls the output
voltage during power-up. Upon power-on, the DAC is placed in
tristate (its reference inputs are disconnected), and its output is
clamped to AGND through a ~6 kΩ resistor. The DAC remains
in this state until programmed otherwise via the control
register. This is a useful feature in applications where it is
important to know the state of the DAC output while it is in the
process of powering up.
CONFIGURING THE AD5781
After power-on, the AD5781 must be configured to put it into
normal operating mode before programming the output. To do
this, the control register must be programmed. The DAC is
removed from tristate by clearing the DACTRI bit, and the
output clamp is removed by clearing the OPGND bit. At this
point, the output goes to VREFN unless an alternative value is first
programmed to the DAC register.
DAC OUTPUT STATE
The DAC output can be placed in one of three states, controlled
by the DACTRI and OPGND bits of the control register, as
Table 16. AD5781 Output State Truth Table
DACTRI
OPGND
Output State
0
Normal operating mode.
0
1
Output is clamped via ~6 kΩ to AGND.
1
0
Output is in tristate.
1
Output is clamped via ~6 kΩ to AGND.
LINEARITY COMPENSATION
The integral nonlinearity (INL) of the AD5781 can vary
according to the applied reference voltage span; the LIN COMP
bits of the control register can be programmed to compensate
for this variation in INL. The specifications in this data sheet
are obtained with LIN COMP = 0000 for reference spans up to
and including 10 V and with LIN COMP = 1100 for a reference
span of 20 V. The default value of the LIN COMP bits is 0000.
OUTPUT AMPLIFIER CONFIGURATION
There are a number of different ways that an output amplifier
can be connected to the AD5781, depending on the voltage
references applied and the desired output voltage span.
Unity Gain Configuration
Figure 50 shows an output amplifier configured for unity gain,
in this configuration the output spans from VREFN to VREFP.
A1
6.8k 6.8k
R1
RFB
18-BIT
DAC
VREFPS
VREFPF
VREFP
VREFN
VREFNS
AD5781
1/2 AD8676
AD8675,
ADA4898-1,
ADA4004-1
1/2 AD8676
VREFNF
RFB
INV
VOUT
09
2-
05
4
Figure 50. Output Amplifier in Unity Gain Configuration
A second unity gain configuration for the output amplifier is
one that removes an offset from the input bias currents of the
amplifier. It does this by inserting a resistance in the feedback
path of the amplifier that is equal to the output resistance of the
DAC. The DAC output resistance is 3.4 kΩ. By connecting R1
and RFB in parallel, a resistance equal to the DAC resistance is
available on-chip. Because the resistors are all on one piece of
silicon, they are temperature coefficient matched. To enable this
mode of operation, the RBUF bit of the control register must be set
to Logic 1. Figure 51 shows how the output amplifier is connected
to the AD5781. In this configuration, the output amplifier is in
unity gain and the output spans from VREFN to VREFP. This unity
gain configuration allows a capacitor to be placed in the
amplifier feedback path to improve dynamic performance.
18-BIT
DAC
VREFPS
10pF
VREFPF
VREFP
VREFN
VREFNS
AD5781
1/2 AD8676
AD8675,
ADA4898-1,
ADA4004-1
1/2 AD8676
VREFNF
VOUT
RFB
VOUT
09
2-
05
5
INV
6.8k
R1
Figure 51. Output Amplifier in Unity Gain with Amplifier Input Bias Current
Compensation
相關PDF資料
PDF描述
RCM08DRTF-S13 CONN EDGECARD 16POS .156 EXTEND
ADZS-BF548-MPSKIT KIT STARTER MULTIMEDIA BF548
SCRH3D16A-1R5 INDUCTOR SMD 1.5UH 1.55A 100KHZ
HSM06DRKI-S13 CONN EDGECARD 12POS .156 EXTEND
ADZS-BF549-EZLITE KIT EZLITE ADZS-BF549
相關代理商/技術參數
參數描述
EVAL-AD5790SDZ 制造商:Analog Devices 功能描述:AD5790 DAC EVALUATION BOARD 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD, Silicon Manufacturer:Analog Devices, Silicon Core 制造商:Analog Devices 功能描述:AD5790, DAC, EVALUATION BOARD, Silicon Manufacturer:Analog Devices, Silicon Core Number:(Not Applicable), Kit Application Type:(Not Available), Application Sub Type:DAC, Features:20-bit Voltage Output DAC, Integrated Precision , RoHS Compliant: Yes
EVAL-AD5791SDZ 功能描述:BOARD EVAL FOR AD5791 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5821AEBZ 功能描述:BOARD EVAL FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5821EBZ 功能描述:BOARD EVALUATION FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5821EBZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:120 mA, Current Sinking, 10-Bit, I2C DAC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*