- 您現在的位置：買賣IC網 > PDF目錄16847 > EVAL-AD1940MINIBZ (Analog Devices Inc)BOARD EVAL AD1940 MINI SIGMADSP PDF資料下載
參數資料
| 型號： | EVAL-AD1940MINIBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 27/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL AD1940 MINI SIGMADSP |
| 標準包裝： | 1 |
| 系列： | SigmaDSP® |
| 主要目的： | 音頻，音頻處理 |
| 嵌入式： | 是，DSP |
| 已用 IC / 零件： | AD1940 |
| 主要屬性： | 單芯片多通道 28/56 位音頻 DSP |
| 次要屬性： | 均衡，交叉，低音增強，多頻帶動態處理，延遲等 |
| 已供物品： | 板，線纜，CD，電源，USB 適配器 |
| 產品目錄頁面： | 775 (CN2011-ZH PDF) |
| 相關產品： | AD1940YSTZ-ND - IC DSP AUDIO 16CH/28BIT 48-LQFP AD1940YSTZRL-ND - IC DSP AUDIO 16CH/28BIT 48-LQFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD1940/AD1941
Rev. B | Page 33 of 3
6
INITIALIZATION
POWER-UP SEQUENCE
The AD1940/AD1941 have a built-in power-up sequence that
initializes the contents of all internal RAMs. During this time,
the contents of the internal program boot ROM are copied to
the internal program RAM memory and the parameter RAM
(all 0s) is filled with values from its associated boot ROM. The
default boot ROM program simply copies the serial inputs to
the serial outputs with no processing. The data memories are
also cleared during this time.
The boot sequence, which starts on the rising edge of the
RESETB pin, lasts for 8,192 cycles of the signal on the MCLK
pin at start-up. Assuming even the slowest possible signal on
this pin, a 64 × fS clock, the boot sequence still completes before
the PLL locks to the input clock. Since the boot sequence
requires a stable master clock, the user should avoid writing to
or reading from the registers until the MCLK input signal has
settled and the PLL has locked. The PLL takes approximately
3 ms to lock. Coming out of reset, the clock mode is imme-
diately set by the PLL_CTRL0, PLL_CTRL1, and PLL_CTRL2
pins. Reset is synched to the falling edge of the internal MCLK.
The power-up default signal processing flow in the AD1940/
AD1941 simply takes the eight inputs and copies these signals
to the 16 digital outputs, as shown in Figure 28.
04607-0-004
SDATA_IN0
SDATA_IN1
SDATA_IN2
SDATA_IN3
SDATA_OUT0
SDATA_OUT1
SDATA_OUT2
SDATA_OUT3
SDATA_OUT4
SDATA_OUT5
SDATA_OUT6
SDATA_OUT7
Figure 28. Default Program Signal Flow
SETTING MASTER CLOCK/PLL MODE
The AD1940/AD1941’s MCLK input feeds a PLL, which gen-
erates the 1536 × fS clock to run the DSP core. In normal
operation, the input to MCLK must be one of the following;
64 × fS, 256 × fS, 384 × fS, or 512 × fS, where fS is the input
sampling rate. The mode is set on PLL_CTRL0, PLL_CTRL1,
and PLL_CTRL2, according to Table 41. If the
AD1940/AD1941 are set to receive double-rate signals (by
reducing the number of program steps/sample by a factor of 2
using the core control register), then the master clock
frequencies must be either 32 × fS, 128 × fS, 192 × fS, or 256 × fS.
If the AD1940/AD1941 are set to receive quad rate signals (by
reducing the number of program steps/sample by a factor of 4
using the core control register), then the master clock
frequencies must be 16 × fS, 64 × fS, 96 × fS, or 128 × fS. On
power-up, a clock signal must be present on MCLK so that the
AD1940/AD1941 can complete their initialization routine. The
PLL can also run in bypass mode, where the clock present on
MCLK is fed directly to the
DSP core, although this setting is not recommended for
normal operation.
Table 41. PLL Modes
MCLK Input
PLL_CTRL2
PLL_CTRL1
PLL_CTRL0
64 × fS
0
256 × fS
0
1
0
384 × fS
1
512 × fS
1
0
Bypass
1
0
1 X = don’t care
The clock mode should not be changed without also resetting
the AD1940/AD1941. If the mode is changed on the fly, a click
or pop may result on the outputs. The state of the PLL_CTRLx
pins should be changed while RESETB is held low.
VOLTAGE REGULATOR
The AD1940/AD1941 include an on-board voltage regulator
that allows the chip to be used in systems where a 2.5 V supply
is not available, but 3.3 V or 5 V is. The only external
components needed for this are a PNP transistor such as a
ZX5T953G, a single capacitor, and a single resistor. The
recommended design for the voltage regulator is shown in
Figure 29. The 10 μF and 100 nF capacitors shown in this
schematic are recommended for bypassing, but are not
necessary for operation. Here, VDD is the main system voltage
(3.3 V or 5 V) and should be connected to VSUPPLY. 2.5 V is
generated at the transistor’s collector, which is connected to the
VDD pins, PLL_VDD and VSENSE. The reference voltage on
VREF is 1.15 V and is generated by the regulator. A 1 nF
capacitor should be connected between this pin and ground.
VDRIVE is connected to the base of the PNP transistor. A 1 kΩ
resistor should be connected between VDRIVE and VSUPPLY.
10
μF
10
μF
100nF
1nF
1k
Ω
AD1940/AD1941
DVDD
ZX5T953G
04607-0-009
VSU
PPLY
VR
EF
V
DRIV
E
VSEN
SE
VD
D
+
PLL_VDD
Figure 29. Voltage Regulator Design
相關PDF資料 |
PDF描述 |
|---|---|
| ADN8830ACPZ | IC CTRLR THERMO COOLER 32-LFCSP |
| MAX674CSA+T | IC VREF SERIES PREC 10V 8-SOIC |
| RSC06DRXN-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| SDR1006-100ML | INDUCTOR POWER 10UH 2.6A SMD |
| AD9520-4/PCBZ | BOARD EVAL FOR AD9520-4 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD1941EB | 制造商:Analog Devices 功能描述:EVAL BD SIGMADSPMULTICHANAUDIO PROCESSOR - Bulk |
| EVAL-AD1953EB | 制造商:Analog Devices 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT ((NS)) |
| EVAL-AD1953EBZ | 制造商:Analog Devices 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk |
| EVAL-AD1954EB | 制造商:Rochester Electronics LLC 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk 制造商:Analog Devices 功能描述: |
| EVAL-AD1955EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD1955 制造商:Analog Devices 功能描述:EVAL BOARD FOR 24 BIT 192KHZ DAC 120 DB - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL BOARD FOR 24 BIT 192KHZ DAC 120 DB - Bulk |
發布緊急采購，3分鐘左右您將得到回復。