- 您現在的位置：買賣IC網 > PDF目錄97907 > EL7571C Programmable PWM Controller PDF資料下載
參數資料
| 型號： | EL7571C |
| 英文描述： | Programmable PWM Controller |
| 中文描述： | 可編程PWM控制器 |
| 文件頁數： | 3/23頁 |
| 文件大小： | 480K |
| 代理商： | EL7571C |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁
11
EL7571C
Programmable PWM Controller
E
L
75
71
C
For safe and reliable operation, PD must be less than the
capacitor’s data sheet rating.
Input Inductor, L2
The input inductor (L2) isolates switching noise from
the input supply line by diverting buck converter input
ripple current into the input capacitor. Buck regulators
generate high levels of input ripple current because the
load is connected directly to the supply through the top
switch every cycle, chopping the input current between
the load current and zero, in proportion to the duty cycle.
The input inductor is critical in high current applications
where the ripple current is similarly high. An exclu-
sively large input inductor degrades the converter’s load
transient response by limiting the maximum rate of
change of current at the converter input. A 1.5H input
inductor is sufficient in most applications.
Output Capacitor, C2
During steady state operation, output ripple current is
much less than the input ripple current since current flow
is continuous, either via the top switch or the bottom
switch. Consequently, output capacitor power dissipa-
tion is less of a concern than the input capacitor’s.
However, low ESR is still required for applications with
very low output ripple voltage or transient response
requirements. Output ripple voltage is given by:
where:
IRIP = output ripple current
ESROUT = output capacitor ESR
During a transient response, the output voltage spike is
determined by the ESR and the equivalent series induc-
tance (ESL) of the output capacitor in addition to the rate
of change and magnitude of the load current step. The
output voltage transient is given by:
where:
ESROUT = output capacitor ESR
ESL = output capacitor ESL
IOUT = output current step
di/dt = rate of change of output current
Power MOSFET, Q1 and Q2
The EL7571C incorporates a boot-strap gate drive
scheme to allow the usage of N-channel MOSFETs. N-
channel MOSFETs are preferred because of their rela-
tive low cost and low on resistance. The largest amount
of the power loss occurs in the power MOSFETs, thus
low on resistance should be the primary characteristic
when selecting power MOSFETs. In the boot-strap gate
drive scheme, the gate drive voltage can only go as high
as the supply voltage, therefore in a 5V system, the
MOSFETs must be logic level type, Vgs<4.5V. In addi-
tion to on resistance and gate to source threshold, the
gate to source capacitance is also very important. In the
region when the output current is low (below5A),
switching loss is the dominant factor. Switching loss is
determined by:
where:
C is the gate to source capacitance of the MOSFET
V is the supply voltage
F is the switching frequency
Another undesirable reason for a large MOSFET gate to
source capacitance is that the on resistance of the MOS-
FET driver can not supply the peak current required to
turn the MOSFET on and off fast. This results in addi-
tional MOSFET conduction loss. As frequency
increases, this loss also increases which leads to more
power loss and lower efficiency.
Finally, the MOSFET must be able to conduct the maxi-
mum current and handle the power dissipation.
The EL7571C is designed to boot-strap to 12V for 12V
only input converters. In this application, logic level
MOSFETs are not required.
Table below lists a few popular MOSFETs and their crit-
ical specifications.
VRIP
IRIP ESROUT
×
=
VOUT
ESROUT IOUT ESL
di
dt
----
×
+
×
=
P
CV
2
F
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| EL84 | OUTPUT PENTODE PENTHODE DE SORTIE ENDPENTODE |
| EL883B | High Accuracy Fast Buffer |
| EL883G | High Gain Fast FET Input Op Amp |
| ELANSC310 | Elan SC310 - Elan SC310 Single-Chip. 32-Bit. PC/AT Microcontroller |
| ELANSC410 | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL7571CM | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| EL7571CM-T13 | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| EL7571CMZ | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| EL7571CMZ-T13 | 功能描述:IC CTRLR PWM PROGRAMMABLE 20SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| EL7581 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3-Channel DC-DC Converter |
發布緊急采購，3分鐘左右您將得到回復。