參數資料
型號: EL7464CRE-T13
英文描述: Monolithic 4 Amp DC:DC Step-down Regulator
中文描述: 單片4安培直流:DC降壓穩壓器
文件頁數: 8/18頁
文件大小: 1196K
代理商: EL7464CRE-T13
16
EL7564C
Monolithic 4 Amp DC:DC Step-down Regulator
E
L
75
64
C
Thermal Management
The EL7564CM utilizes “fused lead” packaging tech-
nology in conjunction with the system board layout to
achieve a lower thermal resistance than typically found
in standard SO20 packages. By fusing (or connecting)
multiple external leads to the die substrate within the
package, a very conductive heat path is created to the
outside of the package. This conductive heat path MUST
then be connected to a heat sinking area on the PCB in
order to dissipate heat out and away from the device.
The conductive paths for the EL7564CM package are
the fused leads: # 6, 7, 11, 12, and 13. If a sufficient
amount of PCB metal area is connected to the fused
package leads, a junction-to-ambient resistance of
43°C/W can be achieved (compared to 85°C/W for a
standard SO20 package). The general relationship
between PCB heat-sinking metal area and the thermal
resistance for this package is shown in the Performance
Curves section of this data sheet. It can be readily seen
that the thermal resistance for this package approaches
an asymptotic value of approximately 43°C/W without
any airflow, and 33°C/W with 100 LFPM airflow. Addi-
tional information can be found in Application Note #8
(Measuring the Thermal Resistance of Power Surface-
Mount Packages). For a thermal shutdown die junction
temperature of 135°C, and power dissipation of 1.5W,
the ambient temperature can be as high as 70°C without
airflow. With 100 LFPM airflow, the ambient tempera-
ture can be extended to 85°C.
The EL7564CRE utilizes the 28-pin HTSSOP package.
The majority of heat is dissipated through the heat pad
exposed at the bottom of the package. Therefore, the
heat pad needs to be soldered to the PCB. The thermal
resistance for this package is better than that of SO20.
Actual test results are available from Elantec Applica-
tions staff. The actual junction temperature can be
measured at VTJ pin.
Since the thermal performance of the IC is heavily
dependent on the board layout, the system designer
should exercise care during the design phase to ensure
that the IC will operate under the worst-case environ-
mental conditions.
Layout Considerations
The layout is very important for the converter to func-
tion properly. Power Ground ( ) and Signal Ground (---)
should be separated to ensure that the high pulse current
in the Power Ground never interferes with the sensitive
signals connected to Signal Ground. They should only
be connected at one point (normally at the negative side
of either the input or output capacitor.)
The trace connected to the FB pin is the most sensitive
trace. It needs to be as short as possible and in a “quiet”
place, preferably between PGND or SGND traces.
In addition, the bypass capacitor connected to the VDD
pin needs to be as close to the pin as possible.
The heat of the chip is mainly dissipated through the
PGND pins. Maximizing the copper area around these
pins is preferable. In addition, a solid ground plane is
always helpful for the EMI performance.
The demo board is a good example of layout based on
these principles. Please refer to the EL7564C Applica-
tion Brief for the layout.
相關PDF資料
PDF描述
EL7551C Monolithic 1 Amp DC:DC Step-down Regulator
EL7551CU Monolithic 1 Amp DC:DC Step-down Regulator
EL7556AC Adjustable Synchronous DC:DC Switching Regulator
EL7556BCM-T13 Integrated Adjustable 6 Amp Synchronous Switcher
EL7556BCM Integrated Adjustable 6 Amp Synchronous Switcher
相關代理商/技術參數
參數描述
EL7501 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:100V High Side Driver
EL7501CN 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:100V High Side Driver
EL7501CS 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:100V High Side Driver
EL7512 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High Frequency PWM Step-Up Regulator
EL7512C 制造商:ELANTEC 制造商全稱:ELANTEC 功能描述:High Frequency PWM Step-Up Regulator