- 您現在的位置：買賣IC網 > PDF目錄97902 > EL4095CN FOIL RESISTOR, 500, .1% PDF資料下載
參數資料
| 型號： | EL4095CN |
| 英文描述： | FOIL RESISTOR, 500, .1% |
| 中文描述： | 視頻增益控制/前后/復用器 |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 457K |
| 代理商： | EL4095CN |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
EL4095C
Video Gain ControlFaderMultiplexer
Applications Information
Contd
In fact the gain control internal circuitry is very
complex Here is a representation of the termi-
nals
Representation of Gain Control
Inputs VG and VG
4095 – 28
For
gain
control
inputs
between
g
05V
(g90
mA) the diode bridge is a low impedance
and all of the current into VG flows back out
through VG When gain control inputs exceed
this amount the bridge becomes a high imped-
ance as some of the diodes shut off and the VG
impedance rises sharply from the nominal 55 K
X
to over 500 K
X This is the condition of gain con-
trol overdrive
The actual circuit produces a
much sharper overdrive characteristics than does
the simple diode bridge of this representation
The gain input has a 20 MHz b3 dB bandwidth
and 17 ns risetime for inputs to g045V When
the gain control voltage exceeds the 0% or 100%
values a 70 ns overdrive recovery transient will
occur when it is brought back to linear range If
quicker gain overdrive response is required the
Force control inputs of the EL4095 can be used
Force Inputs
The Force inputs completely override the VGAIN
setting and establish maximum attainable 0%
and 100% gains for the two input channels They
are activated by a TTL logic low on either of the
FORCE pins and perform the analog switching
very quickly and cleanly FORCEA causes 100%
gain on the A channel and 0% on the B channel
FORCEB does the reverse but there is no de-
fined output state when FORCEA and FORCEB
are simultaneously asserted
The Force inputs do not incur recovery time pen-
alties and make ideal multiplexing controls A
typical use would be text overlay where the A
channel is a video input and the B channel is
digitally created text data The FORCEA input
is set low normally to pass the video signal but
released to display overlay data The gain control
can be used to set the intensity of the digital
overlay
Other Applications Circuits
The EL4095 can also be used as a variable-gain
single input amplifier If a 0% lower gain ex-
treme is required
one channel’s input should
simply be grounded Feedback resistors must be
connected to both bVIN terminals the EL4095
will not give the expected gain range when a
channel is left unconnected
This circuit gives a05 to a20 gain range and
is useful as a signal leveller where a constant
output level is regulated from a range of input
amplitudes
13
相關PDF資料 |
PDF描述 |
|---|---|
| EL4095CS | Video Gain Control/Fader/Multiplexer |
| EL41 | EL41 |
| EL4331C | Triple 2:1 Mux-Amp AV = 1 |
| EL4331CS | Triple 2:1 Mux-Amp AV = 1 |
| EL4332 | Triple 2:1 300 MHz Mux-Amp AV =2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL4095CS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Video Gain Control/Fader/Multiplexer |
| EL40A128S5L6X3PR | 制造商:Avago Technologies 功能描述:INCREMENTAL ENCODER - Bulk |
| EL40PO-30MA-AD24-00415UL | 制造商:Fuji Electric 功能描述: |
| EL41 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:EL41 |
| EL41009 | 制造商:Honeywell Sensing and Control 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。