- 您現在的位置：買賣IC網 > PDF目錄97902 > EL2450C 125 MHz Single Supply Quad Op Amps(125 MHz，單電源四路運算放大器) PDF資料下載
參數資料
| 型號： | EL2450C |
| 英文描述： | 125 MHz Single Supply Quad Op Amps(125 MHz，單電源四路運算放大器) |
| 中文描述： | 125 MHz的單電源四路運算放大器（125兆赫，單電源四路運算放大器） |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 469K |
| 代理商： | EL2450C |
11
EL2250C/EL2450C
125 MHz Single Supply Dual/Quad Op Amps
EL2250C/EL2450C
Applications Information
Product Description
The EL2250C/EL2450C are part of a family of the
industries fastest single supply operational amplifiers.
Connected in voltage follower mode, their -3dB band-
width is 125 MHz while maintaining a 275 V/
s slew
rate. With an input and output common mode range that
includes ground, these amplifiers were optimized for
single supply operation, but will also accept dual sup-
plies. They operate on a total supply voltage range as
low as +2.7V or up to +12V. This makes them ideal for
+3V applications, especially portable computers.
While many amplifiers claim to operate on a single sup-
ply, and some can sense ground at their inputs, most fail
to truly drive their outputs to ground. If they do succeed
in driving to ground, the amplifier often saturates, caus-
ing distortion and recovery delays. However, special
circuitry built into the EL2250C/EL2450C allows the
output to follow the input signal to ground without
recovery delays.
Power Supply Bypassing And Printed Circuit
Board Layout
As with any high-frequency device, good printed circuit
board layout is necessary for optimum performance.
Ground plane construction is highly recommended. Lead
lengths should be as short as possible. The power supply
pins must be well bypassed to reduce the risk of oscilla-
tion. The combination of a 4.7
F tantalum capacitor in
parallel with a 0.1
F ceramic capacitor has been shown
to work well when placed at each supply pin. For single
supply operation, where the GND pin is connected to the
ground plane, a single 4.7
F tantalum capacitor in paral-
lel with a 0.1
F ceramic capacitor across the VS+ and
GND pins will suffice.
For good AC performance, parasitic capacitance should
be kept to a minimum. Ground plane construction should
be used. Carbon or Metal-Film resistors are acceptable
with the Metal-Film resistors giving slightly less peak-
ing and bandwidth because of their additional series
inductance. Use of sockets, particularly for the SO pack-
age should be avoided if possible. Sockets add parasitic
inductance and capacitance which will result in some
additional peaking and overshoot.
Supply Voltage Range and Single-Supply
Operation
The EL2250C/EL2450C have been designed to operate
with supply voltages having a span of greater than 2.7V,
and less than 12V. In practical terms, this means that the
EL2250C/EL2450C will operate on dual supplies ranging
from
±1.35V to ±6V. With a single-supply, the
EL2250C/EL2450C will operate from +2.7V to +12V.
Performance has been optimized for a single +5V supply.
Pins 8 and 4 are the power supply pins on the EL2250C.
The positive power supply is connected to pin 8. When
used in single supply mode, pin 4 is connected to
ground. When used in dual supply mode, the negative
power supply is connected to pin 4.
Pins 4 and 11 are the power supply pins on the
EL2450C. The positive power supply is connected to pin
4. When used in single supply mode, pin 11 is connected
to ground. When used in dual supply mode, the negative
power supply is connected to pin 11.
As supply voltages continue to decrease, it becomes nec-
essary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL2250C/EL2450C have an input voltage range that
includes the negative supply and extends to within 1.2V
of the positive supply. So, for example, on a single +5V
supply, the EL2250C/EL2450C have an input range
which spans from 0V to 3.8V.
The output range of the EL2250C/EL2450C is also quite
large. It includes the negative rail, and extends to within
1V of the top supply rail with a 1 k
load. On a +5V
supply, the output is therefore capable of swinging from
0V to +4V. On split supplies, the output will swing
±4V.
If the load resistor is tied to the negative rail and split
supplies are used, the output range is extended to the
negative rail.
Choice Of Feedback Resistor, RF
The feedback resistor forms a pole with the input capac-
itance. As this pole becomes larger, phase margin is
reduced. This increases ringing in the time domain and
peaking in the frequency domain. Therefore, RF has
some maximum value which should not be exceeded for
相關PDF資料 |
PDF描述 |
|---|---|
| EL2460CN | Dual/Quad 130 MHz Current Feedback Amplifiers |
| EL2460CS | Dual/Quad 130 MHz Current Feedback Amplifiers |
| EL2460C | Quad 130 MHz Current Feedback Amplifiers(130 MHz，四路電流反饋放大器) |
| EL2470CN | 70 MHz/1 mA Current Mode Feedback Amplifiers |
| EL2470CS | 70 MHz/1 mA Current Mode Feedback Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL2450CN | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply Dual/Quad Op Amps |
| EL2450CS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply Dual/Quad Op Amps |
| EL2450CS-T13 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply Dual/Quad Op Amps |
| EL2450CS-T7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| EL2460 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual/Quad 130MHz Current Feedback Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。