- 您現在的位置：買賣IC網 > PDF目錄93320 > ECM014 PDF資料下載
參數資料
| 型號： | ECM014 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 115K |
| 代理商： | ECM014 |
EiC Corp. A Subsidiary of EiC Enterprises, Ltd.
45738 Northport Loop West, Fremont, CA 94538
Phone: (510) 979-8999
Fax: (510) 979-8902
www.eiccorp.com
8
ECM010
WCDMA
3.5V POWER AMPLIFIER MODULE
PRELIMINARY DATA SHEET
SS-000411-000
Revision C
If a lower gain PAM is used, the driver needs to provide more power, at the expense of
more operation current and possible degradation in ACPR.
Therefore the ECM010 can replace a lower gain PAM, this allows the driver to
work at a lower output power and provide better ACPR, this improved performance
offers more design margin in the transmitter chain.
IV. Easy Shut Down and Low Leakage Current
The Vcc pin of the PAM is connected directly to the battery, therefore a shut down
FET is not required. A voltage is applied to the Vref pin, which then brings up the
quiescent current. A Q control pin switches the quiescent current to 50mA for the low
output power range. The low power range is below 16dBm; the high power range is
from 16dBm to full power.
Removing the voltage applied to Vref pin, the quiescent current will drop to a small
leakage current, typically <10uA. The low leakage current of the PAM allows for a
longer standby time for the phone.
V. General Application
The PAM requires a minimal number of external components. Both the input and
output are dc-blocked within the PAM as shown in the function diagram. The input pin is
connected to ground through a shunt inductor within the PAM.
ECM010 is designed with a low quiescent current of 50mA typical in the low
power mode. At full WCDMA power of 27dBm, the operation current will be greater than
500mA. Therefore it is a “quasi class B” or “deep class AB” amplifier. The operation
current increases with output power.
WCDMA signal has a time varying amplitude. The peak power is 4dB above the
average RF power (it can be more accurately defined by PDF, power density function).
As the peak power is clipped by the amplifier saturation power level, the distortion of the
signal will cause the ACPR to deteriorate rapidly. Therefore the P1dB (as tested by a
SINE wave) of the amplifier should be over 31dBm to provide good ACPR at 27 dBm of
output power.
A 100pF capacitor is required adjacent to the Vcc2 pin. In addition, a large
capacitor (>uF) is required. The WCDMA signal has a time-varying amplitude; therefore
the PAM draws on operation current corresponding to the instantaneous demand by the
RF power. The large capacitor near-by is the electric charge reservoir, providing current
on demand. The long electrical path from battery behaves as a large inductor; the
instantaneous demand on current will cause a voltage drop, resulting in poor ACPR.
On the evaluation board, a large shunt capacitor is added to protect the Vref pin
from power supply over-voltage during ON/OFF. This is similar but different from the
ESD. Therefore the rise and fall time test of the power down feature needs to be tested
with the shunt capacitor on Vref pin removed.
相關PDF資料 |
PDF描述 |
|---|---|
| ECM018 | |
| ECM051 | |
| ECM060 | |
| ECM064 | |
| ECM068 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ECM02DRAN | 功能描述:CONN EDGECARD 4POS R/A .156 SLD RoHS:是 類別:連接器，互連式 >> Card Edge 系列:- 標準包裝:1 系列:- 卡類型:非指定 - 雙邊 類型:母頭 Number of Positions/Bay/Row:18 位置數:36 卡厚度:0.062"（1.57mm） 行數:2 間距:0.156"（3.96mm） 特點:卡擴展器 安裝類型:板邊緣，跨騎式安裝 端子:焊接 觸點材料:磷青銅 觸點表面涂層:金 觸點涂層厚度:10µin（0.25µm） 觸點類型：:環形波紋管 顏色:黑 包裝:托盤 法蘭特點:- 材料 - 絕緣體:聚酰胺（PA9T） 工作溫度:-65°C ~ 125°C 讀數:雙 |
| ECM02DREN | 功能描述:CONN EDGECARD 4POS .156 EYELET RoHS:是 類別:連接器，互連式 >> Card Edge 系列:- 標準包裝:1 系列:- 卡類型:非指定 - 雙邊 類型:母頭 Number of Positions/Bay/Row:28 位置數:56 卡厚度:0.062"（1.57mm） 行數:2 間距:0.156"（3.96mm） 特點:- 安裝類型:通孔，直角 端子:焊接 觸點材料:磷青銅 觸點表面涂層:金 觸點涂層厚度:30µin（0.76µm） 觸點類型：:全波紋管 顏色:綠 包裝:托盤 法蘭特點:側面安裝開口，無螺紋，0.125"（3.18mm）直徑 材料 - 絕緣體:聚苯硫醚（PPS） 工作溫度:-65°C ~ 125°C 讀數:雙 |
| ECM02DRKN | 功能描述:CONN EDGECARD 4POS DIP .156 SLD RoHS:是 類別:連接器，互連式 >> Card Edge 系列:- 標準包裝:1 系列:- 卡類型:非指定 - 雙邊 類型:母頭 Number of Positions/Bay/Row:28 位置數:56 卡厚度:0.062"（1.57mm） 行數:2 間距:0.156"（3.96mm） 特點:- 安裝類型:通孔，直角 端子:焊接 觸點材料:磷青銅 觸點表面涂層:金 觸點涂層厚度:30µin（0.76µm） 觸點類型：:全波紋管 顏色:綠 包裝:托盤 法蘭特點:側面安裝開口，無螺紋，0.125"（3.18mm）直徑 材料 - 絕緣體:聚苯硫醚（PPS） 工作溫度:-65°C ~ 125°C 讀數:雙 |
| ECM02DRKN-S13 | 功能描述:CONN EDGECARD 4POS .156 EXTEND RoHS:是 類別:連接器，互連式 >> Card Edge 系列:- 標準包裝:1 系列:- 卡類型:非指定 - 雙邊 類型:母頭 Number of Positions/Bay/Row:40 位置數:80 卡厚度:0.093"（2.36mm） 行數:2 間距:0.100"（2.54mm） 特點:- 安裝類型:面板安裝 端子:焊接孔眼 觸點材料:銅鈹 觸點表面涂層:金 觸點涂層厚度:10µin（0.25µm） 觸點類型：:全波紋管 顏色:藍 包裝:托盤 法蘭特點:側面安裝開口，無螺紋，0.125"（3.18mm）直徑 材料 - 絕緣體:聚對苯二甲酸丁二酯（PBT） 工作溫度:-65°C ~ 125°C 讀數:雙 |
| ECM02DRPN | 功能描述:CONN EDGECARD 4POS DIP .156 SLD RoHS:是 類別:連接器，互連式 >> Card Edge 系列:- 標準包裝:1 系列:- 卡類型:非指定 - 雙邊 類型:母頭 Number of Positions/Bay/Row:6 位置數:12 卡厚度:0.062"（1.57mm） 行數:2 間距:0.156"（3.96mm） 特點:- 安裝類型:通孔 端子:焊接 觸點材料:磷青銅 觸點表面涂層:錫 觸點涂層厚度:100µin（2.54µm） 觸點類型：:全波紋管 顏色:藍 包裝:托盤 法蘭特點:頂部安裝開口，無螺紋，0.125"（3.18mm）直徑 材料 - 絕緣體:聚對苯二甲酸丁二酯（PBT） 工作溫度:-65°C ~ 125°C 讀數:雙 |
發布緊急采購，3分鐘左右您將得到回復。