- 您現在的位置：買賣IC網 > PDF目錄97874 > EB2060X Evaluation board PDF資料下載
參數資料
| 型號： | EB2060X |
| 英文描述： | Evaluation board |
| 中文描述： | 評估板 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 873K |
| 代理商： | EB2060X |
_______________
__ EB-2060x
4
Details are subject to change without notice.
HEADERS / REGULATORS (FIG. 3D)
The EB-2060x features local power regulation to
facilitate operation from a unipolar +10 to +28
VDC supply. Alternatively, auxiliary power may
be applied at J8 (removing bead L7) separating
logic and output power supplies.
Output from
the onboard +5V regulator is available on the J6
test header.
Output from the onboard +3.3V
regulator is available on
the J7 expansion
header. There is capability available to power
external circuits from either the +5V or the +3.3V
supplies or a combination not to exceed a total
current of 0.33A.
Expansion header J7 is provided to monitor or
apply input signals to the DDX-2000.
Jumper
R42 may be removed to pass serial data
provided by an external processor. Test header
J6 is provided to monitor signals output from the
DDX-2000.
Signals INLC, INLD, INRC, INRD
are driven low by the DDX-2000 and are used
for test purposes only. DIP switch SW1 is used
for control functions:
POS1 reverses data
channels when open, normal when closed;
POS2 sets unity gain for test when closed,
normal when open; POS3 forces the DDX-2060
into low power mode when closed, normal when
open; POS4 disables the anticlipping function
when closed, normal when open.
Supervisor U8 is used for power-on-reset,
power-off sequencing, and as a convenient
means of commanded reset via pushbutton.
ADDITIONAL INFORMATION
Bill of Materials
A bill of materials for the evaluation board is
provided in Table 1 for reference.
Note
equivalent
components
from
alternate
manufacturers may be substituted. No warranty
of system performance is implied by Apogee
through use of the reference bill of materials.
Power Dissipation/Heat Sink Requirements
The DDX-2060 is a high efficiency dual channel
design intended for audio applications needs up
to 35 Watts RMS per channel.
The power
dissipation of the device will depend primarily on
the supply voltage, load impedance, and output
modulation level. The thermal performance of
the evaluation board is consistent with a steady-
state duty rating of 25W RMS per channel with
both channels driven into 8
.
The DDX-2060 surface mount package includes
an exposed thermal pad on the bottom of the
device to provide a direct thermal path from the
integrated circuit to the PCB. This pad must be
soldered to a low thermal impedance path at
circuit ground potential for proper operation, e.g.
a PCB ground plane. For continuous duty rated
applications,
careful
consideration
must
be
made to the overall thermal design.
Performance Measurements
Typical performance measurements for the
evaluation board are shown in Figs 4 through
11.
Class
D
amplifiers
produce
measurable
switching distortion outside the audio bandwidth.
Apogee's DDX amplifier uses a patented PWM
modulation scheme that significantly reduces the
size of these products compared to typical Class
D designs. However, in order to obtain accurate
performance
measurements
in
the
audio
bandwidth (i.e., 20Hz to 20kHz) additional
filtering is required.
The Typical Performance data in was taken
using a brick wall filter with a break frequency of
22kHz. This type of filter is often provided as
part of audio measurement systems.
OPERATING INSTRUCTIONS
Refer to Fig. 12 evaluation amplifier assembly
drawing. Attach a regulated power supply at J3
set between +10V and +28VDC. At +28V, the
power supply must be capable of delivering 3A
minimum for two channels.
Attach a digital
audio input source at either the coaxial or optical
S/PDIF connectors.
Select the digital input
source via J2. Connect 8 Ohm speakers to J4
(left speaker) and J5 (right speaker). Configure
SW1 as POS1 closed, POS2,3,4 open.
Note,
the speaker outputs are bridged. Do not ground
any speaker connections, e.g. through an
oscilloscope.
Apply
power,
digital
source
material
and
enjoy!
相關PDF資料 |
PDF描述 |
|---|---|
| EB402 | EB402 Evaluation Board user＇s guide 7/01 |
| EBD12RB8ALFB-1A | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD12RB8ALFB-75 | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD12RB8ALFB-7A | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD25RB4ALFB-1A | SDRAM|DDR|32MX72|CMOS|DIMM|184PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EB2061 | 功能描述:SWITCH PUSHBUTTON DPDT 3A 125V RoHS:是 類別:開關 >> 按鈕 系列:EB 標準包裝:1 系列:A16 類型:標準，發光式 電路:雙刀雙擲 開關功能:開-瞬時 額定電流:5A（AC） 額定電壓 - AC:125V 額定電壓 - DC:- 觸動器類型:方形，按鈕 顏色 - 致動器/蓋:黃 發光類型，顏色:LED，黃 發光電壓:12 VDC 安裝類型:前面板安裝 端接類型:焊接，快速連接 - 0.110"（2.8mm） 防護等級:IP65 - 防塵/防油/防水 特點:- 面板切口尺寸:圓形 - 直徑 16.00mm 包裝:散裝 工作溫度:-10°C ~ 55°C 機械壽命:2,000,000 次循環 電氣壽命:100,000 次循環 其它名稱:A165LAYM12D2 |
| EB-2061 | 制造商:NKK Switches 功能描述:Bulk |
| EB2061-A-J20 | 制造商:NKK 制造商全稱:Nihon Kaiheiki Industry Co. Ltd. 功能描述:Light Touch Miniature Pushbuttons |
| EB2061-A-J21A | 制造商:NKK Switches 功能描述:MINIATURE PUSHBUTTON/BUSHING MOU 制造商:NKK Switches 功能描述:MINIATURE PUSHBUTTON/BUSHING MOUNT |
| EB2061-A-J21A-RO | 功能描述:按鈕開關 DPDT ON-(ON) RoHS:否 制造商:C&K Components 觸點形式:2 NC - 2 NO 開關功能:ON ? OFF 電流額定值:4 A 電壓額定值 AC:12 V to 250 V 電壓額定值 DC:12 V to 50 V 功率額定值: 安裝風格:Through Hole 照明:Illuminated 照明顏色:None IP 等級:IP 40 端接類型:Solder 觸點電鍍:Silver 執行器:Square 蓋顏色: 封裝: 可燃性等級:UL 94 V-0 |
發布緊急采購，3分鐘左右您將得到回復。