- 您現在的位置：買賣IC網 > PDF目錄299014 > E-L6917BD (STMICROELECTRONICS) SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | E-L6917BD |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | ROHS COMPLIANT, SO-28 |
| 文件頁數： | 13/33頁 |
| 文件大小： | 465K |
| 代理商： | E-L6917BD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
L6917B
20/33
as well as for the voltage spikes generated by the distributed inductance along the copper traces are so mini-
mized.
In fact, the further the mosfet is from the device, the longer is the interconnecting gate trace and as a conse-
quence, the higher are the voltage spikes corresponding to the gate pwm rising and falling signals. Even if these
spikes are clamped by inherent internal diodes, propagation delays, noise and potential causes of instabilities
are introduced jeopardizing good system behavior. One important consequence is that the switching losses for
the high side mosfet are significantly increased.
For this reason, it is suggested to have the device oriented with the driver side towards the mosfets and the
GATEx and PHASEx traces walking together toward the high side mosfet in order to minimize distance (see fig
14). In addition, since the PHASEx pin is the return path for the high side driver, this pin must be connected
directly to the High Side mosfet Source pin to have a proper driving for this mosfet. For the LS mosfets, the re-
turn path is the PGND pin: it can be connected directly to the power ground plane (if implemented) or in the
same way to the LS mosfets Source pin. GATEx and PHASEx connections (and also PGND when no power
ground plane is implemented) must also be designed to handle current peaks in excess of 2A (30 mils wide is
suggested).
Gate resistors of few ohms help in reducing the power dissipated by the IC without compromising the system
efficiency.
Figure 14. Device orientation (left) and sense nets routing (right)
The placement of other components is also important:
– The bootstrap capacitor must be placed as close as possible to the BOOTx and PHASEx pins to mini-
mize the loop that is created.
– Decoupling capacitor from Vcc and SGND placed as close as possible to the involved pins.
– Decoupling capacitor from VCCDR and PGND placed as close as possible to those pins. This capacitor
sustains the peak currents requested by the low-side mosfet drivers.
– Refer to SGND all the sensible components such as frequency set-up resistor (when present) and also
the optional resistor from FB to GND used to give the positive droop effect.
– Connect SGND to PGND on the load side (output capacitor) to avoid undesirable load regulation effect
and to ensure the right precision to the regulation when the remote sense buffer is not used.
– An additional 100nF ceramic capacitor is suggested to place near HS mosfet drain. This helps in reduc-
ing noise.
– PHASE pin spikes. Since the HS mosfet switches in hard mode, heavy voltage spikes can be observed
on the PHASE pins. If these voltage spikes overcome the max breakdown voltage of the pin, the device
can absorb energy and it can cause damages. The voltage spikes must be limited by proper layout, the
use of gate resistors, Schottky diodes in parallel to the low side mosfets and/or snubber network on the
low side mosfets, to a value lower than 26V, for 20nSec, at Fosc of 600kHz max.
s
Current Sense Connections.
Remote Buffer: The input connections for this component must be routed as parallel nets from the FBG/FBR
Towards HS mosfet
(3 0 mils wide)
Towards LS mosfet
(30 mils wide)
Towards HS mosfet
(3 0 mils wide)
To LS mosfet
(or sense resistor)
To regulated output
To LS mosfet
(or sense resistor)
相關PDF資料 |
PDF描述 |
|---|---|
| E-L8150TR | BRUSHLESS DC MOTOR CONTROLLER, PDSO28 |
| E-L9935013TR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| E1L33-3BOA6-02 | T-1 SINGLE COLOR LED, BLUE, 3 mm |
| E1L35-3G0A7-02 | T-1 SINGLE COLOR LED, GREEN, 3 mm |
| E1L35-3G0A5-02 | T-1 SINGLE COLOR LED, GREEN, 3 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E-L6917BDTR | 功能描述:DC/DC 開關控制器 Prog Dual-Phase Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| E-L6919E | 功能描述:電流型 PWM 控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| E-L6919ETR | 功能描述:電流型 PWM 控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| E-L6920D | 功能描述:直流/直流開關轉換器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| E-L6920DTR | 功能描述:直流/直流開關轉換器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。