參數資料
型號: DSPIC33FJ12MC201-I/P
廠商: Microchip Technology
文件頁數: 40/155頁
文件大?。?/td> 0K
描述: IC DSPIC MCU/DSP 12K 20DIP
產品培訓模塊: Asynchronous Stimulus
特色產品: PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝: 22
系列: dsPIC™ 33F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 40 MIP
連通性: I²C,IrDA,SPI,UART/USART
外圍設備: 高級欠壓探測/復位,電機控制 PWM,QEI,POR,PWM,WDT
輸入/輸出數: 15
程序存儲器容量: 12KB(12K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 4x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 20-DIP(0.300",7.62mm)
包裝: 管件
產品目錄頁面: 651 (CN2011-ZH PDF)
配用: DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
2007-2011 Microchip Technology Inc.
DS70265E-page 25
dsPIC33FJ12MC201/202
3.5
Arithmetic Logic Unit (ALU)
The dsPIC33FJ12MC201/202 ALU is 16 bits wide and
is capable of addition, subtraction, bit shifts, and logic
operations. Unless otherwise mentioned, arithmetic
operations are 2’s complement in nature. Depending
on the operation, the ALU can affect the values of the
Carry (C), Zero (Z), Negative (N), Overflow (OV), and
Digit Carry (DC) Status bits in the SR register. The C
and DC Status bits operate as Borrow and Digit Borrow
bits, respectively, for subtraction operations.
The ALU can perform 8-bit or 16-bit operations,
depending on the mode of the instruction that is used.
Data for the ALU operation can come from the W
register array or data memory, depending on the
addressing mode of the instruction. Likewise, output
data from the ALU can be written to the W register array
or a data memory location.
Refer to the “16-bit MCU and DSC Programmer’s Ref-
erence Manual”
(DS70157) for information on the SR
bits affected by each instruction.
The dsPIC33FJ12MC201/202 CPU incorporates hard-
ware support for both multiplication and division. This
includes a dedicated hardware multiplier and support
hardware for 16-bit-divisor division.
3.5.1
MULTIPLIER
Using the high-speed 17-bit x 17-bit multiplier of the
DSP engine, the ALU supports unsigned, signed or
mixed-sign operation in several MCU multiplication
modes:
16-bit x 16-bit signed
16-bit x 16-bit unsigned
16-bit signed x 5-bit (literal) unsigned
16-bit unsigned x 16-bit unsigned
16-bit unsigned x 5-bit (literal) unsigned
16-bit unsigned x 16-bit signed
8-bit unsigned x 8-bit unsigned
3.5.2
DIVIDER
The divide block supports 32-bit/16-bit and 16-bit/16-bit
signed and unsigned integer divide operations with the
following data sizes:
1.
32-bit signed/16-bit signed divide
2.
32-bit unsigned/16-bit unsigned divide
3.
16-bit signed/16-bit signed divide
4.
16-bit unsigned/16-bit unsigned divide
The quotient for all divide instructions ends up in W0
and the remainder in W1. 16-bit signed and unsigned
DIV
instructions can specify any W register for both
the 16-bit divisor (Wn) and any W register (aligned)
pair (W(m + 1):Wm) for the 32-bit dividend. The divide
algorithm takes one cycle per bit of divisor, so both
32-bit/16-bit and 16-bit/16-bit instructions take the
same number of cycles to execute.
3.6
DSP Engine
The DSP engine consists of a high-speed 17-bit x
17-bit multiplier, a barrel shifter and a 40-bit adder/
subtracter (with two target accumulators, round and
saturation logic).
The dsPIC33FJ12MC201/202 is a single-cycle instruc-
tion flow architecture; therefore, concurrent operation
of the DSP engine with MCU instruction flow is not pos-
sible. However, some MCU ALU and DSP engine
resources can be used concurrently by the same
instruction (e.g., ED, EDAC).
The DSP engine can also perform inherent accumula-
tor-to-accumulator operations that require no additional
data. These instructions are ADD, SUB, and NEG.
The DSP engine has options selected through bits in
the CPU Core Control register (CORCON), as listed
below:
Fractional or integer DSP multiply (IF)
Signed or unsigned DSP multiply (US)
Conventional or convergent rounding (RND)
Automatic saturation on/off for ACCA (SATA)
Automatic saturation on/off for ACCB (SATB)
Automatic saturation on/off for writes to data
memory (SATDW)
Accumulator Saturation mode selection (ACC-
SAT)
A block diagram of the DSP engine is shown in
TABLE 3-1:
DSP INSTRUCTIONS
SUMMARY
Instruction
Algebraic
Operation
ACC Write
Back
CLR
A = 0
Yes
ED
A = (x – y)2
No
EDAC
A = A + (x – y)2
No
MAC
A = A + (x * y)
Yes
MAC
A = A + x2
No
MOVSAC
No change in A
Yes
MPY
A = x * y
No
MPY
A = x 2
No
MPY.N
A = – x * y
No
MSC
A = A – x * y
Yes
相關PDF資料
PDF描述
MS27484T22B53P CONN PLUG 53POS STRAIGHT W/PINS
VE-B0V-IX-F2 CONVERTER MOD DC/DC 5.8V 75W
PIC24FJ64GA002-E/SP IC PIC MCU FLASH 64K 28-SDIP
MS27497E14B37S CONN RCPT 37POS WALL MNT W/SCKT
PIC24EP64MC202-I/SS MCU 16BIT 64KB FLASH 28SSOP
相關代理商/技術參數
參數描述
DSPIC33FJ12MC201T-E/SS 制造商:Microchip Technology Inc 功能描述:
dsPIC33FJ12MC201T-I/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 12KBFLSH 1KB RAM 16B Motor Cntrl DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ12MC201T-I/SS 功能描述:數字信號處理器和控制器 - DSP, DSC 12KBFLSH 1KB RAM 16B Motor Cntrl DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ12MC202-E/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 12KB FLSH 1024BRAM 16B nanoWatt RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ12MC202-E/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 12KB FLSH 1024BRAM 16B nanoWatt RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT