參數資料
型號： DS87C550-QCL+
廠商： Maxim Integrated Products
文件頁數： 10/49頁
文件大小： 0K
描述： IC MCU EPROM ADC/PWM HS 68-PLCC
標準包裝： 18
系列： 87C
核心處理器： 8051
芯體尺寸： 8-位
速度： 33MHz
連通性： EBI/EMI，SIO，UART/USART
外圍設備： 電源故障復位，PWM，WDT
輸入/輸出數： 55
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： OTP
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 4.5 V ~ 5.5 V
數據轉換器： A/D 6x10b
振蕩器型： 外部
工作溫度： 0°C ~ 70°C
封裝/外殼： 68-LCC（J 形引線）
包裝： 管件
DS87C550 EPROM High-Speed Microcontroller with ADC and PWM
18 of 49
Switchback
One of the other unique features included on the DS87C550 is Switchback. Simply, Switchback when
enabled will allow serial ports and interrupts to automatically switch back from divide-by-1024 (PMM) to
divide-by-4 (standard speed operation). This feature makes it very convenient to use the Power
Management Mode in real time applications. Of course to return to a divide-by-4 clock rate from divide-
by-1024 PMM, software can simply select the CD1 & CD0 clock control bits to the 4 clocks per cycle
state. However, the DS87C550 provides hardware alternatives for automatic Switchback to standard
speed operation.
The Switchback feature is enabled by setting the SFR bit SWB (PMR.5) to a 1. Once it is enabled and
when PMM is selected, there are two possible events that can cause an automatic switchback to divide-
by-4 mode. First, if an interrupt occurs and is set so that it will be acknowledged, this event will cause the
system clock to revert from PMM to divide-by-4 mode. For example, if INT0 is enabled then Switchback
will occur on INT0 . However, if INT0 is not enabled, then activity on INT0 will not cause switchback to
occur.
A Switchback can also occur when an enabled UART detects the start bit indicating the beginning of an
incoming serial character or when the SBUF register is loaded initiating a serial transmission. Note that a
serial character’s start bit does not generate an interrupt. This occurs only on reception of a complete
serial word. The automatic Switchback on detection of a start bit allows hardware to correct baud rates in
time for a proper serial reception or transmission. So with Switchback enabled and a serial port enabled,
the automatic switch to normal speed operation occurs automatically in time to receive or transmit a
complete serial character as if nothing special had happened.
Once Switchback causes the processor to make the transition back to divide-by-4 mode, software must
modify SFR bits CD1 & CD0 to re-enter Power Management Mode. However, if a serial port is in the
process of transmitting or receiving a character, then this change back to PMM will not be allowed as the
hardware prevents a write to CD1 & CD0 during any serial port activity.
Since the reception of a serial start bit or an interrupt priority lockout is normally undetectable by
software in an 8051, the Status register features several new flags that are useful. These are described
below.
Status
Information in the Status register assists decisions about switching into PMM. This register contains
information about the level of active interrupts and the activity on the serial ports.
The DS87C550 supports three levels of interrupt priority. These levels are Power-fail, High, and Low.
Status bits STAT.7-5 indicate the service status of each level. If PIP (Power-fail Interrupt Priority;
STATUS.7) is a 1, then the processor is servicing this level. If either HIP (High Interrupt Priority;
STATUS.6) or LIP (Low Interrupt Priority; STATUS.5) is high, then the corresponding level is in
service.
Software should not rely on a lower priority level interrupt source to remove PMM (Switchback) when a
higher level is in service. Check the current priority service level before entering PMM. If the current
service level locks out a desired Switchback source, then it would be advisable to wait until this condition
clears before entering PMM.
相關PDF資料
PDF描述
DS89C450-ENL IC MCU FLASH 64KB 33MHZ 44-TQFP
DS9034PCI IC SRAM NV TIMEKEEPING POWERCAP
DS9034PCX PCM W/CRYSTAL NV SRAM SNAP-ON
DS9092L+ IBUTTON PROBE PANEL MOUNT W/LED
DS9092T# IBTN PROBE W/TACTILE FEEDBACK
相關代理商/技術參數
參數描述
DS87C550-QCL+ 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS87C550-QCW 制造商:Maxim Integrated Products 功能描述:DS87C550 WAIVERED FOR LS & MARKING - Rail/Tube
DS87C550-QNL 功能描述:IC MCU EPROM ADC/PWM HS 68-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:87C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件
DS88 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
DS8800 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual Voltage Level Translator
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*