- 您現在的位置：買賣IC網 > PDF目錄1916 > DS8102+ (Maxim Integrated Products)IC MODULATOR/DECODER 16-TSSOP PDF資料下載
參數資料
| 型號： | DS8102+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/9頁 |
| 文件大小： | 0K |
| 描述： | IC MODULATOR/DECODER 16-TSSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 96 |
| 類型： | 調制器 |
| 應用： | 電量測量 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 16-TSSOP |
| 包裝： | 管件 |
| 其它名稱： | 90-08102+XPX |
DS8102
Dual Delta-Sigma Modulator and Encoder
_______________________________________________________________________________________
7
Internal/External Voltage Reference
Selection
The configuration pin APDREF selects whether the
DS8102 uses its internal voltage reference or an exter-
nal voltage reference provided at VREF when perform-
ing conversions. If the internal voltage reference is
selected, the internal reference is buffered and driven
out at VREF, and can be used by external devices if
desired.
Table 2 summarizes the modes of operation for the
DS8102 based on the APDREF input. The level at
APDREF should be set when the DS8102 is in shut-
down mode.
Internal/External Clock Selection
The configuration input pin CLKSEL selects whether the
DS8102 uses the internal 8MHz oscillator or an external
clock (provided at CLKIO) when performing conver-
sions. If the internal 8MHz oscillator is selected, the
internal clock is driven out at CLKIO and can be used
by external devices if desired.
Table 3 summarizes the modes of operation for the
DS8102 based on the CLKSEL input. The level at
CLKSEL should be set when the DS8102 is in shutdown
mode.
Manchester Encoder
Once the DS8102 enters active mode, it begins gener-
ating a Manchester-encoded bit stream on the MNOUT
pin. This bit stream is output at a rate equal to the
selected clock frequency divided by 4, so, for example,
if the internal 8MHz oscillator is selected as the DS8102
clock source, a new bit is output on MNOUT approxi-
mately every 500ns.
Bit values are encoded as either low-to-high transitions
(for bit values of 1) or high-to-low transitions (for bit val-
ues of 0). The transition from low-to-high or high-to-low
occurs halfway through the bit time slot.
As shown in Figure 1, the Manchester-encoded bit-
stream output on MNOUT contains three interleaved bit
streams. These bit streams, in the order that they are
output, are as follows:
1) SYNC—Synchronization bit stream containing alter-
nating 0s and 1s.
2) CHAN0—Pulse-density-modulated output from ana-
log channel 0.
3) CHAN1—Pulse-density-modulated output from ana-
log channel 1.
Both modulator outputs are always included in the bit
stream, even if only one of them is being used by the
application. This means that the maximum bit-rate out-
put for either modulator channel over MNOUT is
fCLK/12 as shown in Figure 1.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line is either a best straight-line fit or a line
drawn between the endpoints of the transfer function
once offset and gain errors have been nullified.
Offset Error
For an ideal converter, the first transition occurs at 0.5
LSB above zero. Offset error is the amount of deviation
between the measured first transition point and the
ideal point.
Power-Supply Rejection Ratio
Power-supply rejection ratio (PSRR) is the ratio of
changes in the power supply (V) to changes in the con-
verter output (V). It is typically measured in decibels.
RST PIN
APDREF PIN
DS8102 MODE
0
X
Shutdown.
1
0
Operation using internal voltage reference (VREF output buffer enabled).
1
Operation using external voltage reference (VREF output buffer disabled).
Table 2. Voltage Reference Selection and Operating Modes
CLKSEL PIN
DS8102 CLOCK SOURCE
CLKIO PIN MODE
0
Internal 8MHz oscillator
Output: Drives out 8MHz clock.
1
External clock (provided at CLKIO)
Input: Accepts external clock.
Table 3. Clock Source Selection
相關PDF資料 |
PDF描述 |
|---|---|
| DS8113-JNG+ | IC INTERFACE SMART CARD 28-TSSOP |
| DS8313-RRX+ | IC INTERFACE SMART CARD 28-SOIC |
| DS8500-JND+T&R | IC MODEM HART SGL 3.6V 20-TQFN |
| DS87C520-ENL | IC MCU EPROM/ROM 33MH IND 44TQFP |
| DS87C530-ECL+ | IC MCU EPR/ROM W/RTC 33MZ 52TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS8102+ | 功能描述:編碼器、解碼器、復用器和解復用器 Dual Delta-Sigma Modulator & Encoder RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| DS811 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS8113 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Smart Card Interface |
| DS8113_10 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Smart Card Interface |
| DS8113-JNG+ | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。