參數資料
型號： DS80C310-MCL
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 33 MHz, MICROCONTROLLER, PDIP40
封裝： 0.600 INCH, PLASTIC, DIP-40
文件頁數： 19/23頁
文件大小： 1255K
代理商： DS80C310-MCL
DS80C310
5 of 23
COMPATIBILITY
The DS80C310 is a fully static CMOS 8051-compatible microcontroller designed for high performance.
In most cases the DS80C310 can drop into an existing socket for the 80C31 or 80C32 to improve the
operation significantly. In general, software written for existing 8051-based systems works without
modification on the DS80C310. The exception is critical timing since the High-Speed Micro performs its
instructions much faster than the original for any given crystal selection. The DS80C310 runs the
standard 8051 family instruction set and is pin compatible with DIP, PLCC or TQFP packages. The
DS80C310 is a streamlined version of the DS80C320. It maintains upward compatibility but has fewer
peripherals.
The DS80C310 provides three 16-bit timer/counters, a full-duplex serial port, and 256 bytes of direct
RAM. I/O ports have the same operation as a standard 8051 product. Timers will default to a 12-clock per
cycle operation to keep their timing compatible with original 8051 family systems. However, timers are
individually programmable to run at the new 4 clocks per cycle if desired.
The DS80C310 provides several new hardware functions that are controlled by Special Function
registers. A summary of the Special Function Registers is provided in Table 2.
PERFORMANCE OVERVIEW
The DS80C310 features a high-speed 8051 compatible core. Higher speed comes not just from increasing
the clock frequency, but from a newer, more efficient design.
This updated core does not have the dummy memory cycles that are present in a standard 8051. A
conventional 8051 generates machine cycles using the clock frequency divided by 12. In the DS80C310,
the same machine cycle takes four clocks. Thus the fastest instruction, 1 machine cycle, executes three
times faster for the same crystal frequency. Note that these are identical instructions. The majority of
instructions on the DS80C310 will see the full 3 to 1 speed improvement. Some instructions will get
between 1.5 and 2.4 to 1 improvement. All instructions are faster than the original 8051.
The numerical average of all opcodes gives approximately a 2.5 to 1 speed improvement. Improvement of
individual programs will depend on the actual instructions used. Speed-sensitive applications would make
the most use of instructions that are three times faster. However, the sheer number of 3 to 1 improved
opcodes makes dramatic speed improvements likely for any code. These architecture improvements and
0.8
m CMOS produce a peak instruction cycle in 121 ns (8.25 MIPs). The Dual Data Pointer feature
also allows the user to eliminate wasted instructions when moving blocks of memory.
INSTRUCTION SET SUMMARY
All instructions in the DS80C310 perform the same functions as their 8051 counterparts. Their effect on
bits, flags, and other status functions is identical. However, the timing of each instructio n is different.
This applies both in absolute and relative number of clocks.
For absolute timing of real time events, the timing of software loops can be calculated using a table in the
High-Speed Microcontroller User’s Guide. However, counter/timers default to run at the older 12 clocks
per increment. In this way, timer-based events occur at the standard intervals with software executing at
higher speed. Timers optionally can run at 4 clocks per increment to take advantage of faster processor
operation.
The relative time of two instructions might be different in the new architecture than it was previously. For
example, in the original architecture the “MOVX A, @ DPTR” instruction and the “MOV direct, direct”
instruction used two machine cycles or 24 oscillator cycles. Therefore, they required the same amount of
相關PDF資料
PDF描述
DS9080A INTERCONNECTION DEVICE
DS9081A INTERCONNECTION DEVICE
DS9085V INTERCONNECTION DEVICE
DS9081V INTERCONNECTION DEVICE
DS9082A INTERCONNECTION DEVICE
相關代理商/技術參數
參數描述
DS80C310-QCG 功能描述:8位微控制器 -MCU High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C310-QCG/T&R 制造商:Maxim Integrated Products 功能描述:MICRO HI SPD 310 44PLCC 25MHZ TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 25MHZ 44-PLCC 制造商:Maxim Integrated Products 功能描述:8-bit Microcontrollers - MCU High-Speed
DS80C310-QCG/T&R 功能描述:8位微控制器 -MCU High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C310-QCG+ 功能描述:8位微控制器 -MCU High-Speed RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C310-QCG+T&R 制造商:Maxim Integrated Products 功能描述:MXMDS80C310-QCG+T&R HIGH SPEED MICRO-CON 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 44PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 25MHZ 44-PLCC 制造商:Maxim Integrated Products 功能描述:8-bit Microcontrollers - MCU High-Speed
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*