- 您現在的位置：買賣IC網 > PDF目錄1916 > DS4301Z-200 (Maxim Integrated Products)IC POT DIG NV 200K 32POS 8-SOIC PDF資料下載
參數資料
| 型號： | DS4301Z-200 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/7頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DIG NV 200K 32POS 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 接片： | 32 |
| 電阻（歐姆）： | 200k |
| 電路數： | 1 |
| 溫度系數： | 標準值 ±250 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 3 線（芯片選擇，遞增，增/減） |
| 電源電壓： | 2.4 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
DS4301
Detailed Description
The DS4301 is a single nonvolatile digital potentiome-
ter. This 32-position linear potentiometer has an end-to-
end resistance of 200k
, and operates over a wide
2.4V to 5.5V supply voltage range. The wiper position is
controlled by the three interface pins (U/D, CS, and
INC), and the wiper setting can be stored in EEPROM
on command.
Power-Up
On power-up, once a stable supply voltage of VCC MIN
has been reached, the stored wiper setting is loaded
from the EEPROM within tWLT. Also on power-up, the
DS4301 wiper control pins become active approximate-
ly tPU after a stable supply voltage of VCC MIN has
been reached.
Wiper Control
Adjusting the wiper of the DS4301 involves using the
three control pins (U/D, CS, and INC). See the Timing
Diagram in Figure 2. To enable wiper adjustment, a
high-to-low transition on the CS pin is required. Hold
CS low for the duration of the communication. Doing
this enables the INC pin to change the wiper position.
Set the U/D pin high to increment or low to decrement
the wiper position. The state of the U/D pin should be
set more than tDI before the INC signal is transitioned
from high to low. After the CS pin is active low, a high-
to-low transition on the INC pin moves the wiper in the
direction dictated by the U/D pin. Continue to pulse
INC (high to low) until the desired wiper position is
reached. On the last edge, hold the INC line low. With
the desired wiper position set, there are two ways to
proceed. One method terminates communication with-
out allowing the value of the current wiper position to
be written to the EEPROM. This is done by transitioning
the CS signal to the high state before bringing the INC
signal high. As long as the state of the CS pin is high
before the state of the INC pin goes high, the current
wiper setting is not written to EEPROM. Because the
current wiper setting was not stored to the NV memory,
the previously stored wiper setting, not the current
wiper setting, is loaded from memory if power is cycled
to the device
The other method is used to store a new wiper setting
in the EEPROM. This is done by bringing the state of
the INC pin high for a time of tIC before bringing the
state of the CS pin high. Once the states of both CS
and INC pins are high, the current wiper setting is
stored in EEPROM after a time of tWST. If power is
Nonvolatile, 32-Position Digital Potentiometer
6
_____________________________________________________________________
VCC
GND
CS
INC
U/D
CONTROL
LOGIC UNIT
NONVOLATILE
MEMORY
5-BIT
WIPER
SETTING
POS 31
POS 0
H
L
W
VCC
Figure 1. Block Diagram
CS
INC
U/D
tCI
tIL
tIH
tF
tIC
tWST
tCPH
tDI
tR
WIPER STORAGE
CONDITION
WIPER NON-STORAGE
CONDITION
WIPER POSITION
POSITION X
POSITION X + 1
POSITION X
tIW
tIK
POSITION X - 1
VIL
VIL
VIH
tCLP
Figure 2. Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| DS4520E+TRL | IC I/O EXPANDER I2C 9B 16TSSOP |
| DS4550E+ | IC I/O EXPANDER I2C 9B 20TSSOP |
| DS4830T+ | MCU 16B CTRL CALIBR MON 40-TQFN |
| DS5000FP-16 | IC MODULE MICRO 16MHZ FLATPACK |
| DS5000T-32-16+ | IC MPU W/RTC 32KB 16MHZ 40-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4302 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302U-019 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302U-020 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302Z-019 | 功能描述:IC DAC 5-BIT SGL 0-1.9V 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:3,000 系列:nanoDAC™ 設置時間:80µs 位數:18 數據接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極 采樣率（每秒）:- 產品目錄頁面:784 (CN2011-ZH PDF) 配用:EVAL-AD5680EBZ-ND - BOARD EVAL FOR AD5680 其它名稱:AD5680BRJZ-2REEL7TR |
| DS4302Z-019/T&R | 制造商:Maxim Integrated Products 功能描述:IC DAC 5-BIT SGL 0-1.9V 8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。