- 您現在的位置：買賣IC網 > PDF目錄1916 > DS3908N+T&R (Maxim Integrated Products)IC POT DUAL DIGITAL 14-TDFN PDF資料下載
參數資料
| 型號： | DS3908N+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DUAL DIGITAL 14-TDFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 接片： | 64 |
| 電阻（歐姆）： | 100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 50 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 14-TDFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
DS3908
Dual, 64-Position Nonvolatile Digital
Potentiometer with Buffered Outputs
10
____________________________________________________________________
Byte Read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition above, and the master transmits an ACK
using the bit write definition to receive additional data
bytes. The master must NACK the last byte read to ter-
minated communication so the slave will return control
of SDA to the master.
Slave Address Byte: Each slave on the I2C bus
responds to a slave address byte sent immediately fol-
lowing a start condition. The slave address byte con-
tains the slave address in the most significant 7 bits
and the R/W bit in the least significant bit.
The DS3908’s slave address is determined by the state
of the A0, A1, and A2 address pins as shown in Figure 1.
Address pins connected to GND result in a ‘0’ in the
corresponding bit position in the slave address.
Conversely, address pins connected to VCC result in a
‘1’ in the corresponding bit positions.
When the R/W bit is 0 (such as in A0h), the master is
indicating it will write data to the slave. If R/W = 1, (A1h
in this case), the master is indicating it wants to read
from the slave.
If an incorrect slave address is written, the DS3908 will
assume the master is communicating with another I2C
device and ignore the communication until the next
start condition is sent.
Memory Address: During an I2C write operation to the
DS3908, the master must transmit a memory address to
identify the memory location where the slave is to store
the data. The memory address is always the second
byte transmitted during a write operation following the
slave address byte.
I2C Communication
Writing a Single Byte to a Slave: The master must
generate a start condition, write the slave address byte
(R/W = 0), write the memory address, write the byte of
data, and generate a stop condition. The master must
read the slave’s acknowledgement during all byte write
operations.
When writing to the DS3908, the potentiometer will
adjust to the new setting once it has acknowledged the
new data that is being written, and the EEPROM (used
to make the setting nonvolatile) will be written following
the stop condition at the end of the write command. To
change the setting without changing the EEPROM, ter-
minate the write with a repeated start condition before
the next stop condition occurs. Using a repeated start
condition prevents the 20ms (maximum) delay required
for the EEPROM write cycle to finish.
If the master continues to write data to the DS3908,
without generating a stop condition, then the same reg-
ister will be overwritten.
Acknowledge Polling: Any time an EEPROM byte is
written, the DS3908 requires the EEPROM write time
(tW) after the stop condition to write the contents of the
byte to EEPROM. During the EEPROM write time, the
device will not acknowledge its slave address because
it is busy. It is possible to take advantage of this phe-
nomenon by repeatedly addressing the DS3908, which
allows communication to continue as soon as the
DS3908 is ready. The alternative to acknowledge
polling is to wait for a maximum period of tW to elapse
before attempting to access the device.
EEPROM Write Cycles: The DS3908’s EEPROM write
cycles are specified in the Nonvolatile Memory
Characteristics table. The specification shown is at the
worst-case temperature. It is capable of handling many
additional writes at room temperature.
Reading a Single Byte from a Slave: Unlike the write
operation that uses the specified memory address byte
to define where the data is to be written, the read oper-
ation occurs at the present value of the memory
address pointer. To read a single byte from the slave,
the master generates a start condition, writes the slave
address byte with R/W = 1, reads the data byte with a
NACK to indicate the end of the transfer, and generates
a stop condition.
Manipulating the Address Pointer for Reads: A
dummy write cycle can be used to force the address
pointer to a particular value. To do this, the master gen-
erates a start condition, writes the slave address byte
(R/W = 0), writes the memory address where it desires
to read, generates a repeated start condition, writes the
slave address byte (R/W = 1), reads data with ACK or
NACK as applicable, and generates a stop condition.
See Figure 3 for a read example using the repeated
start condition to specify the memory location.
Applications Information
Power-Supply Decoupling
To achieve the best results when using the DS3908,
decouple the power supply with a 0.01F or 0.1F
capacitor. Use a high-quality, ceramic, surface-mount
capacitor if possible. Surface-mount components mini-
mize lead inductance, which improves performance,
and ceramic capacitors tend to have adequate high-
frequency response for decoupling applications.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3930E | IC POT NV HEX I/O MEM 20-TSSOP |
| DS4301Z-200 | IC POT DIG NV 200K 32POS 8-SOIC |
| DS4520E+TRL | IC I/O EXPANDER I2C 9B 16TSSOP |
| DS4550E+ | IC I/O EXPANDER I2C 9B 20TSSOP |
| DS4830T+ | MCU 16B CTRL CALIBR MON 40-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3911 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Temperature-Controlled, Nonvolatile, I2C Quad DAC |
| DS3911T+ | 功能描述:ADC / DAC多通道 Fast APD Bias RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| DS3911T+T | 功能描述:ADC / DAC多通道 Fast APD Bias RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| DS3920 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Fast Current Mirror |
| DS3920_1112 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Fast Current Mirror |
發布緊急采購，3分鐘左右您將得到回復。