- 您現在的位置：買賣IC網 > PDF目錄9560 > DS3150T (Maxim Integrated Products)IC LIU T3/E3/STS-1 48-TQFP PDF資料下載
參數資料
| 型號： | DS3150T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 26/28頁 |
| 文件大小： | 0K |
| 描述： | IC LIU T3/E3/STS-1 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 250 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁
DS3150
7 of 28
1.1 Receiver
Interfacing to the Line. The receiver can be transformer-coupled or capacitor-coupled to the line.
Typically, the receiver interfaces to the incoming coaxial cable (75
W) through a 1:2 step-up transformer.
Figure 1-2 shows the arrangement of the transformer and other recommended interface components. The
device expects the incoming signal to be in B3ZS- or HDB3-coded AMI format.
Optional Preamp. The receiver can be used in monitoring applications, which typically have series
resistors that result in a resistive loss of approximately 20dB. When the RMON input pin is high, the
receiver compensates for this resistive loss by applying flat gain to the incoming signal before sending the
signal to the equalizer block.
Adaptive Equalizer. The adaptive equalizer applies both frequency-dependent gain and flat gain to
offset signal losses from the coaxial cable and provides a signal of nominal amplitude and pulse shape to
the clock and data recovery block. The equalizer circuitry automatically adapts to coaxial cable losses
from 0 to 15dB, which translates into 0 to 380 meters (DS3), 0 to 440 meters (E3), or 0 to 360 meters
(STS-1) of coaxial cable (AT&T 734A or equivalent). The equalizer can perform direct (0 meter)
monitoring of the transmitter output signal.
Clock and Data Recovery. The clock and data recovery (CDR) block takes the amplified, equalized
signal from the equalizer and produces separate clock, positive data and negative data signals. The CDR
requires a master clock (44.736MHz for DS3, 34.368MHz for E3, 51.840MHz for STS-1). If the signal
on MCLK is toggling, the device selects the MCLK signal as the master clock. If MCLK is wired high or
left floating, the device uses the signal on the TCLK pin as the master clock. If MCLK is wired low, the
device takes its master clock from an internal oscillator. The selected master clock is also used by the
jitter attenuator.
Loss-of-Signal Detector. The receiver contains both analog and digital LOS detectors. The analog
LOS detector resides in the equalizer block. If the incoming signal level is less than a signal level
approximately 24dB below nominal, analog loss-of-signal (ALOS) is declared. The ALOS signal cannot
be directly examined, but when ALOS occurs the equalizer squelches the recovered data, forcing all zeros
out of the clock and data recovery circuitry and subsequently causing digital loss-of-signal (DLOS),
which is indicated on the
LOS pin. ALOS clears when the incoming signal level is greater than or equal
to a signal level approximately 18dB below nominal.
The digital loss-of-signal detector declares DLOS when it detects 175
±75 consecutive zeros in the
recovered data stream. When DLOS occurs, the receiver asserts the
LOS pin. DLOS is cleared when there
are no excessive zero occurrences over a span of 175
±75 clock periods. An excessive zero occurrence is
defined as three or more consecutive zeros in the DS3 and STS-1 modes and four or more consecutive
zeros in the E3 mode. The
LOS pin is deasserted when the DLOS condition is cleared.
The requirements of ANSI T1.231 and ITU-T G.775 for DS3 LOS defects are met by the DLOS detector,
which asserts
LOS when it counts 175
±75 consecutive zeros coming out of the clock and data recovery
block and clears
LOS when it counts 175
±75 consecutive pulse intervals without excessive zero
occurrences.
The requirements of ITU-T G.775 for E3 LOS defects are met by a combination of the ALOS detector
and the DLOS detector as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B6H-MY-S | CONVERTER MOD DC/DC 52V 50W |
| VI-25F-MX-F4 | CONVERTER MOD DC/DC 72V 75W |
| VI-26X-CU-B1 | CONVERTER MOD DC/DC 5.2V 200W |
| VE-B6F-MY-S | CONVERTER MOD DC/DC 72V 50W |
| VI-26W-CU-B1 | CONVERTER MOD DC/DC 5.5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3150T+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TC1 | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TC1+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TN | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TN+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。